Vermont Casting EWF30 installation instructions Limited Lifetime Warranty

Page 31

LIMITED LIFETIME Warranty

For Vermont Castings

EWF30, Sequoia II, Non-Catalytic Woodburning Fireplace

Limited Lifetime Warranty

CFM Corporation warrants that all refractory brick and material used in this product will be warranted against deterioration not resulting from physical damage or overloading of the wood fireplace for the lifetime of this product. This coverage includes the components of the EverBurn System: “shoe, fountain, and fireback. Coverage is provided only to the original purchaser.

Limited 3 Year Warranty

All cast iron parts are warranted for a period of three years against breakage, cracking or burn-through.

Limited 1 Year Warranty

The following parts of the woodburning fireplace are war- ranted to be free of defects in material and workmanship for a period of one year from the date you receive it: The handles, glass door panels, door gasketing and porcelain finish. Any of these items found to be defective will be repaired or replaced at no charge, upon the return of the part with postage prepaid to a Vermont Castings Autho- rized Dealer.

Any parts repaired or replaced during the limited warranty period will be warranted under the terms of the limited warranty for a period not to exceed the remaining term of the original limited warranty or six (6) months, whichever is longer.

Exclusions & Limitations

1.This warranty is non-transferable.

2.This warranty does not cover misuse of the fireplace. Misuse includes overfiring, which will result if the fireplace is used in such a manner as to cause one or more of the plates to glow red. Overfiring can be iden- tified later by warped plates and areas where the paint pigments has burned off. Overfiring in enamel com- ponents is identified by bubbling, cracking, chipping and discoloration of the porcelain enamel finish. CFM Corporation offers no warranty on chipping of enamel surfaces. Inspect your woodburning component prior to accepting it for any damage to the enamel.

3.This warranty does not cover misuse of the fireplace as described in the Owners Guide, nor does it cover a fireplace which has been modified unless autho- rized by a CFM Corporation representative in writing. This warranty does not cover damage to the fireplace caused by burning salt saturated wood, chemically treated wood, or any fuel not recommended in the Owners Guide.

4.This warranty does not cover a fireplace repaired by someone other than a Vermont Castings Authorized Dealer.

5.Damage to the unit while in transit is not covered by this warranty but is subject to a claim against the common carrier. Contact Vermont Castings Authorized Dealer from whom you purchased your fireplace or CFM Corporation if the purchase was direct. (Do not operate the fireplace as this may negate the ability to process the claim with the carrier).

6.Claims are not valid where the installation does not conform to local building and fire codes or, in their ab- sence, to the recommendations in our Owners Guide.

7.The salt air environment of coastal areas, or a high- humidity environment, can be corrosive to the porce- lain enamel finish. These conditions can cause rusting of the cast iron beneath the porcelain enamel finish, which will cause the porcelain enamel finish to flake off. This warranty does not cover damage caused by a salt air or high-humidity environment.

8.CFM Corporation shall have no obligation to enhance or update any unit once manufactured.

IN NO EVENT SHALL CFM CORPORATION BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES. ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, ARE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. THIS WARRANTY SUPERCEDES ALL OTHER ORAL OR WRITTEN WARRANTIES.

Some states do not allow the exclusion or limitations of incidental and consequential damages or limitations on how long an implied warranty lasts, so the above limi- tations may not apply to you. This warranty gives you specific rights and you may have other rights, which vary from state to state.

How to Obtain Service

If a defect is noted within the warranty period, the customer should contact a Vermont Castings Authorized Dealer or CFM Corporation if the purchase was direct with the following information:

1.Name, address, and telephone number of the pur- chaser

2.Date of Purchase.

3.Serial number from the label on the back

4.Nature of the defect or damage.

5.Any relevant information or circumstances, e.g., instal- lation, mode of operation when defect was noted.

A warranty claim will then start in process. CFM Corpo- ration reserves the right to withhold final approval of a warranty claim pending a visual inspection of the defect by authorized representatives.

20008662

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents EWF30 Introduction Table of ContentsDrafts Safety InformationPrecautions DescriptionEWF30 Woodburning Fireplace SpecificationsFireplace and chase parts identification Chase InstallationChimney Requirements Offset Installations Ten Foot Rule Planning InformationMounting the Fireplace Planning the Chimney RunInsulating Fireplace Enclosure for Cold Climates InstallationChase Installation Chimney SupportsEB1 Receptacle Hookup Straight-Up Chimney InstallationOffset Installation FramingFraming the Ceiling Hole Positioning, Safety Strips Securing the FireplaceCeiling Chimney Hole Possible Obstructions Cutting the HoleInstallation Precautions Installing Outside Air KitInstallation Instructions Use outside air cover plate to cover air inlet opening Installing the Chimney SystemCanadian Requirements For Insulation Shield Installing the Firestop Spacer Ceiling HoleProper Firestop Spacer Installation Continue Installing Pipe to Complete RunPenetrating the Roof Install Remainder of Chimney SectionsInstall Top Housing or Termination Installing Chimney in a ChaseSide View MantelsExample of Determining Hearth Extension Equiva- lents Hearth InstallationSide Wall Protection Examples of wall shield insulationMinimum Wall Clearances EWF30 Controls OperationAttach Handles DamperBurn Only High-Quality Wood Use the Air Control Settings That Work Best for YouFan Glass DoorsReloading and Reviving a Wood Fire Starting and Maintaining a Wood FireSpecial Tactics for Cold-Climate Heating Remove and Store Ash Safely How to Replace Gaskets MaintenanceCleaning the Glass Adjust the Door Latch PeriodicallyReplace Damaged Door Glass Immediately Clean Chimney System is Safer and Works BetterChimney System Replacing the Door GasketsYearly Spring Cleaning Maintenance ScheduleFireplace Daily Component Description Model Number Chimney ComponentsDescription EWF30 FireplaceRef. Description EWF30 FireplaceGravity Vent Kit Optional AccessoriesFan Kit Screen KitModel Description Trim KitsVermont Castings EWF30 Limited Lifetime Warranty CFM Corporation
Related manuals
Manual 32 pages 28.92 Kb

EWF30 specifications

The Vermont Casting EWF30 is a testament to innovation and craftsmanship in the world of cast iron wood stoves. This highly efficient wood-burning stove combines traditional aesthetics with modern technology, making it a perfect centerpiece for both rustic and contemporary homes. One of the standout features of the EWF30 is its impressive heating capacity. Designed to heat areas up to 2,000 square feet, it is ideal for large spaces, providing consistent warmth during chilly months.

Constructed from high-quality cast iron, the EWF30 offers a durability that only improves with age. This material is known for its excellent heat retention and distribution, resulting in a steady, comfortable warmth. The stove’s classic design includes large ceramic glass windows, allowing users to enjoy the mesmerizing beauty of the fire while safely keeping the warmth inside.

Incorporating advanced technology, the Vermont Casting EWF30 features a clean burning system that significantly reduces emissions. This is a critical aspect for environmentally conscious consumers, as the stove adheres to strict EPA standards, promoting cleaner air and reduced environmental impact. The efficiency of this wood stove is exceptional, with a thermal efficiency rating that maximizes heat output while minimizing fuel usage.

The EWF30 is equipped with a user-friendly air control system, allowing for easy adjustments to the airflow. This system enhances the combustion process, enabling users to achieve the desired flame and heat levels effortlessly. The top-loading design also simplifies the refueling process, making it easier to add wood without disturbing the existing fire.

Aesthetically, the Vermont Casting EWF30 can be customized with various finishes, including traditional black, enamel, and even bold colors, ensuring it fits seamlessly with any interior decor. Additionally, this model includes a removable ash pan, providing a convenient cleaning option.

In summary, the Vermont Casting EWF30 is more than just a wood stove; it is a fusion of tradition and technology. Its heating efficiency, durability, and aesthetic appeal make it a worthy investment for anyone seeking a reliable and stylish heating solution for their home. Whether for ambiance or functionality, the EWF30 is designed to enhance the living experience while respecting the environment.
Top Page Image Contents