Vermont Casting 39LDVR, 43LDVR, 33LDVR Clearance to Combustibles, Mantels, Mantel Chart, Hearth

Clearance to Combustibles

Top of Unit to Ceiling	36” (914mm)
Appliance
Top	0” (0 mm)
Bottom	0” (0 mm)
Side	0” (0 mm)
Back	0” (0 mm)
Venting
Concentric sections of DV Vent
Top, bottom & sides	1” (25 mm)
Rear Vent Applications:
Top	2” (50 mm)
Sides and Bottom	1” (25 mm)

Mantels

The height that a combustible mantel is fitted above the fireplace is dependent on the depth of the mantel. This also applies to the distance between the mantel leg (if fitted) and the fireplace.

For the correct mounting height and widths refer to Figs. 3a and 3b, and the following Mantel Charts.

The fitting of a bay window trim kit does not effect the distances and reference points referred to in the diagram and chart.

Noncombustible mantels and legs may be installed at any height and width around the appliance.

When using paint or lacquer to finish the mantel, such paint or lacquer must be heat resistant to prevent discoloration.

V

W

X

Y

Z

				A B	C D	E
									Fireplace
									Top Louvre As-
									sembly
									Top of Combustion
									Chamber
										CFM146
				Mantel Chart
		Mantel Shelf							Mantel from Top
Ref.	or Breast Plate				Ref.		of Combustion Chamber
			Depth			36/39/43 LDVR				33LDVR
V		10”	(254 mm)		A	17”		(432 mm)		16¹⁄₂” (419 mm)
W		8”	(203 mm)		B	15”		(381 mm)		14¹⁄₂” (368 mm)
X		6”	(152 mm)		C	13”		(330 mm)		12¹⁄₂” (318 mm)
Y		4”	(102 mm)		D	11”		(279 mm)		10¹⁄₂” (267 mm)
Z		2”	(51 mm)		E	9”		(229 mm)		8¹⁄₂” (216 mm)
Fig. 3a		Combustible mantel minimum installation.

LDVR Series Direct Vent Gas Fireplace

		J	I H
Black				G
Surround
				F
Face	Mantel
CFM164a	Leg
Side of		MLK
Combustion Chamber		N
		O

						CFM170
		Mantel		Mantel Leg FromSide
Ref.	Leg Depth		Ref.	of Comb. Opening
F	10”	(254 mm)	K	11¹⁄₂”	(292 mm)
G	8”	(203 mm)	L	9¹⁄₂”	(241 mm)
H	6”	(152 mm)	M	7¹⁄₂”	(191 mm)
I	4”	(102 mm)	N	5¹⁄₂”	(140 mm)
J	2”	(51 mm)	O	3¹⁄₂”	(89 mm)

Fig. 3b Combustible mantel leg minimum installation.

Hearth

A hearth is not mandatory but is recommended for aesthetic purposes. We recommend a noncombustible hearth which projects out 12” (305mm) or more from the front of the fireplace.

Cold climate installation recommendation:

When installing this unit against a non-insulated exterior wall or chase, it is mandatory that the outer walls be insulated to conform to applicable insulation codes.

This appliance may be installed in an aftermarket permanently located, manufactured home or mobile home, where not prohibited by local codes.

This applianceis only for usewiththetypeofgasindicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

The LDVR has been approved for mobile home installations.

10007317 5