Vermont Casting 43LDVR, 39LDVR, 33LDVR Optional Accessories Available, Fan Kits, FK24 Fan Assembly

Page 36

LDVR Series Direct Vent Gas Fireplace

Optional Accessories Available

Fan Kits

FK24 Fan Assembly

This auxiliary fan system increases the efficiency of the circulation of the heated air.

The FK24 fan kit allows variable speed control of the circulation fan and also incorporates a heat sensor in the circuit.

Specifications

115 Volt / 60Hz / 56 Watts

Maintenance

The fan itself does not require regular maintenance, however periodic cleaning of the fan and the surrounding area is required.

Check the area under the control door (lower louvre assembly) and in front of the fan and wipe or vacuum this area at least once a month during the operating season.

Installation

The fan assembly and other components are supplied fully wired, eliminating the need for a licensed electrician to carry out the installation.

If hard wiring the fan using Method B (following) we strongly recommend the use of a licensed electrician.

1.Open the lower louvre assembly. Move the fan & bracket assembly around the gas valve and lines to locate the unit onto the screw studs on the back of the fireplace.

2.Install the thermal sensor under the bottom of the of the firebox, locating it over the two 10mm studs and secure it with nuts.

3.Locate the fan speed control unit. This can be fitted behind the lower louvre assembly as in Figure 52 or located remotely in a conveniently located wall mounted electrical box. Remote location of the speed control will require suitable extension of the component wiring.

4.The power supply may be connected in two ways:

Method A

Route the 6’ lead fitted to the unit to a conveniently located wall socket.

Method B (Using EB-1 Receptacle Box)

The EB-1 receptacle box (Pt. # ZA1200) may be hard wired into the house supply. The fan lead is then plugged into the EB-1 box. For instruction on wiring the EB-1 receptacle box see the earlier chapter in the Installation section of this manual.

Thermal

 

Sensor

Fan

 

 

Valve

 

Fan Speed

Gas

EB-1 Recep-

tacle Box

FP1230 Switch

Lines

 

Fig. 52 FK24 fan placement.

FK12

This auxiliary fan system increases the efficiency of the circulation of the heating air.

The FK12 Fan Assembly is a fixed speed fan system and does not allow for variable speed control. It does not use the speed control unit or the heat sensor used in the FK24 Kit.

Specifications

115 Volts / 60 Hz / 56 Watts.

Maintenance

The fan itself does not require regular maintenance, however periodic cleaning of the fan and the surrounding area is required.

Check the area under the control door (lower louvre assembly) and in front of the fan and wipe or vacuum this area at least once a month during the operating season.

Installation

The fan assembly is supplied fully wired eliminating the need for a licensed electrician to carry out the installation.

1.Open the lower Louvre assembly. Move the fan & bracket assembly around the gas valve and lines to locate the unit against the back wall of the appliance, resting on the base.

2.With the protective cover removed from the self- adhesive ‘Velcro’ strips apply mild pressure to the fan & bracket unit to secure the strips to the metal panels. No further securing is required.

3.Power to the fan can be supplied by plugging the supplied lead into a conveniently located wall socket or by using a hard-wired EB-1 receptacle box.

36

10007317

Image 36
Contents Builder Rear Vent Direct Vent Table of Contents Installation & Operating Instructions Locating Your FireplacePlease Review the Following Carefully Fireplace Dimensions Framing Dimensions33LDVR 36LDVR 39LDVR 43LDVR Mantel Chart Clearance to CombustiblesMantels HearthFraming and Finishing Final Finishing33LDVR / 36LDVR / 39LDVR / 43LDVR Certified To Gas SpecificationsGas Line Installation Remote ON/OFF SwitchAlternate Switch Location InstallationEB-1 Electrical Box Electronic Gas Control ValveGeneral Venting Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationCanadian Installations USA InstallationsGeneral Information Assembling Vent Pipes Flex Vent PipesHow to Use the Vent Graph Twist Lock PipesRear Wall Venting Applications Example aRear Wall Installation Twist Lock Pipe StepRear Wall Vent Installations Flex Vent Pipe StepVertical Sidewall Applications Maximum number of 90 elbows is three Vertical Sidewall Installation Zero clearance sleeve is only required for combustible wallsBelow Grade Installations Measure horizontal length including 2 overlapVertical Through-the-Roof Applications This Gas Fireplace has been approved forVertical Through-the-Roof Installation Typical vertical roof applicationsMin 610 mm Venting Components Glass Cleaning Window Frame Assembly RemovalOperating Instructions Glass InformationInstallation of Logs, Lava Rock & Ember Material Log Identification ChartLog Installation Rial on the burner housing assembly Do not place any of the lava rock mateFlame Characteristics Flame & Temperature AdjustmentOn the burner housing assembly Do not place any of the lava rock material33LDVR Lighting and Operating Instructions To Turn Off Gas To HeaterWhat to do if YOU Smell GAS Lighting Instructions Turning Off the Gas to the ApplianceValve in the on position Troubleshooting Honeywell Millivolt Valve Start CheckYES Troubleshooting the Gas Control System Normal Operation Abnormal OperationFuel Conversion Instructions PSE PilotSIT 820 Nova Gas Control Valve Fig SIT top Convertible PilotMaintenance Cleaning the Standing Pilot Control SystemBurner and Burner Compartment Brass Trim33/36/39/43LDVR Ldvr DescriptionGADT3I0 GADT3J0 GADT3K0 GADT3N0 Fuel Conversion KitsOptional Accessories Available FK24 Fan AssemblyFan Kits Wiring Instructions Remote ControlsCeramic Refractory Kits Appliance Model Kit NameOptional Trim Kits Louvre Accent TrimScreen Door Kit Filigree Louvre KitLimited Lifetime Warranty Product Covered by this WarrantyEfficiency Ratings AFUE%

36LDVR, 33LDVR, 39LDVR, 43LDVR specifications

Vermont Castings has long been synonymous with quality craftsmanship and innovation in the field of heating appliances, particularly in the category of wood and gas stoves. Among their remarkable offerings, the 33LDVR, 39LDVR, 43LDVR, and 36LDVR models stand out, each with unique features that cater to a variety of user needs.

The 33LDVR model features a classic design that complements any space while providing efficient heating. With a maximum output of 15,000 BTUs, it is perfect for smaller rooms. One of its main characteristics is the built-in catalytic combustor, which enhances fuel efficiency and reduces emissions. This model also includes a convenient glass door that allows for a beautiful view of the flames, creating a warm ambiance.

Moving up in size, the 36LDVR offers an increased heating capability of up to 25,000 BTUs. This model retains the same elegance and durability as the 33LDVR, constructed from high-quality cast iron. The 36LDVR is equipped with Vermont Castings’ signature dual combustion system, which maximizes fuel efficiency and minimizes smoke. Additionally, the oversized door enhances visibility while maintaining a robust heat output.

The 39LDVR boasts a larger firebox, providing increased heat capacity and longer burn times. It can accommodate logs up to 18 inches long, making it ideal for those who appreciate long-lasting fires. This model also features a patented top-loading capability, which simplifies the refueling process without interrupting heat output. The advanced air control system allows users to fine-tune the burn rate, enhancing efficiency and managing heat distribution effectively.

Finally, the 43LDVR is the powerhouse of the lineup, with an impressive heating capacity of up to 40,000 BTUs. This model is designed for larger spaces, providing superior heat retention and distribution. It features Vermont Castings' innovative refractory lining, which improves heat retention and provides a longer-burning effect. The 43LDVR also includes a state-of-the-art fan system that promotes consistent warmth throughout the room, ensuring comfort even in the coldest weather conditions.

All four models incorporate Vermont Castings' commitment to environmentally responsible heating, with advanced technology that reduces emissions while maximizing efficiency. The aesthetic design, combined with practical features, makes these units a popular choice for homeowners looking to enhance their living spaces with reliable heating solutions. Whether for ambiance or effective heating, the 33LDVR, 36LDVR, 39LDVR, and 43LDVR models truly exemplify the quality and craftsmanship that Vermont Castings is known for.