Desa Tech CGCFTN Operating Fireplace, For Your Safety Read Before Lighting, Lighting Instructions

Page 17

OPERATING FIREPLACE

For Your Safety Read Before Lighting Lighting Instructions

17

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service techni- cian or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING: You must operate this fireplace with the fireplace screen in place. Make sure fireplace screen is installed before running fireplace.

5.Turn control knob counterclockwise to the PI- LOT position. Press in control knob for five (5) seconds (see Figure 30).

Note: You may be running this fireplace for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will al- low air to bleed from the gas system.

•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

6.With control knob pressed in, push down and release ig- nitor button. This will light pilot. The pilot is attached to the front of burner. If needed, keep pressing ignitor but- ton until pilot lights.

Note: If pilot does not stay lit, refer to Troubleshooting, pages 20 through 22. Also contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Pro- cedure, page 18.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 3 through 7. This fire- place has a safety interlock system. Wait one (1) minute before lighting pilot again.

8.Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

 

Control

Ignitor Button

Knob

NOTICE: During initial operation of new fireplace, burning logs will give off a paper-burning smell. Orange flame will also be present. Open window to

Figure 30 - Control Knob In The OFF Position

Pilot Burner

vent smell. Operate fireplace on HI position to burn off odor. This will only last a few hours.

1.STOP! Read the safety information above.

2.Make sure equipment shutoff valve is fully open.

3.Turn control knob clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information above. If you don’t smell gas, go to the next step.

Ignitor Electrode

Figure 31 - Pilot

Thermocouple

For morevisit www..com

111044-01D

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsProduct Identification Local CodesUnpacking Product FeaturesAssembly Providing Adequate Ventilation AIR for Combustion and VentilationAssembling Hood Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation AIR InstallationCheck GAS Type Ventilation Air From Inside BuildingLocating Fireplace Installation ItemsRough Opening for Installing in Wall BUILT-IN Fireplace InstallationOptional Mantel Installation Mantel Clearances for BUILT-IN InstallationRemoving Upper Louver Assembly Installing Blower Accessory GA3450TRemoving Valve Cover Shield Installing Blower AssemblyOutlet For Built-In InstallationExtension Cord Connecting to GAS SupplyAttaching Wood Base to Solid Floor Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections Lighting Instructions For Your Safety Read Before LightingOperating Fireplace Inspecting Burner Cleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning and MaintenanceCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at Replacement Parts SpecificationsService Hints Technical ServiceModels Cgcftp and Cgcftn Illustrated Parts BreakdownParts List Parts ListParts Centrals Owners Registration Form Postage Required Accessories Warranty Information

CGCFTP, CGCFTN specifications

Desa Tech, an innovator in the field of electronic components, has introduced the CGCFTN and CGCFTP series, designed to meet the varying needs of modern technology applications. These devices are engineered with high-performance features that make them suitable for a wide range of industries, including telecommunications, automotive, and consumer electronics.

One of the standout features of the CGCFTN and CGCFTP series is their impressive frequency range. These components are capable of operating within a broad spectrum, providing users with flexibility and ensuring that they can be leveraged in various high-frequency applications. The advanced design minimizes signal loss and maximizes efficiency, making them ideal for both analog and digital signal processing.

In terms of technology, the CGCFTN and CGCFTP series utilizes cutting-edge semiconductor technology, ensuring high speed and reliability. The components are manufactured using a robust fabrication process that adheres to international quality standards, resulting in devices that not only perform well but also boast long lifespans. The advanced materials used in their construction contribute to their strength, heat resistance, and overall durability.

The CGCFTP variant is particularly notable for its enhanced power handling capabilities, which ensures that it can efficiently manage high power levels without compromising performance. This makes it a valuable asset in high-demand environments, such as telecommunications infrastructure and industrial machinery.

Another characteristic of these components is their compact design, which allows for easy integration into various devices. This small footprint does not sacrifice performance, ensuring that users can achieve their design goals without needing to make substantial compromises on space or weight. Furthermore, both series feature low power consumption, making them environmentally friendly options for modern electronic designs.

Overall, the Desa Tech CGCFTN and CGCFTP series represents a significant advancement in electronic component technology. With features such as wide frequency range, high power handling, and reliable performance, they are well-suited for a multitude of applications. These devices exemplify Desa Tech’s commitment to innovation, quality, and sustainability, making them a preferred choice for engineers and manufacturers in various sectors striving for excellence in their designs.
Top Page Image Contents