Empire Comfort Systems VFP36SP32EP-2 Optional FBB5 Blower Installation Instructions, Wiring

Page 26

OPTIONAL FBB5 BLOWER INSTALLATION INSTRUCTIONS

Attention: Install blower assembly before connecting gas in- let supply line.

Wiring

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, if an exter- nal electrical source is utilized. This appliance is equipped with a three-prong [grounding] plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. For an ungrounded receptacle, an adapter, which has two prongs and a wire for grounding, can be purchased, plugged into the ungrounded receptacle and its wire connected to the receptacle mounting screw. With this wire com- pleting the ground, the appliance cord plug can be plugged into the adapter and be electrically grounded.

Caution: Label all wires prior to disconnection when servic- ing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

Note: Junction box is to be located in the lower compartment of the fireplace and must be pre-wired at time of fireplace in- stallation for use with blower assembly. A standard ON/ OFF wall switch or SCV-1 variable speed control kit should be installed to activate power to the Junction Box and pro- vide power for the operation of the blower assembly. It is recommended that installation of the wiring be performed by a qualified electrician. See Figures 20 and 21.

1.If installed, turn OFF gas supply to fireplace.

2.If applicable, turn OFF electric supply to fireplace.

3.Remove bottom louver from fireplace.

CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRI- CAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLY IS DISCONNECTED. THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LAT- EST EDITION).

To install the blower kit, access the junction box, or install a light kit, remove lower louver as illustrated by figure 21.

A factory included junction box is located on the lower right side of the fireplace. Wiring must be fed through the 7/8" diameter hole provided on the lower side of the fireplace, and secured to the outer wrap with the clamp provided. Leave approximately 6” of wire in the junction box for connection.

Attach black wire to one side of the receptacle and white wire to opposite side of receptacle. The ground wire should be attached to the green (ground) screw. See Figure 20.

Install the receptacle into the junction box as illustrated. Attach cover plate. Place Junction Box so that it is approximately 8 to 12" away from the outer wrap wall. Secure wiring at outer wrap of fireplace with wire clamp provided.

Attention: If installed, do not damage gas inlet supply line when blower assembly is inserted into fireplace. In some cases, removal of the gas inlet supply line may be necessary.

Figure 20

Figure 21

Page 26

26670-0-0110

Image 26
Contents Premium Vent-Free Multi-Sided Fireplaces Table of Contents Carton Contents Hardware PackageImportant Safety Information Do not Tamper with Pilot Light SafetySafety Information for Users of LP-GAS LP-GAS Warning OdorIntroduction Accessories SpecificationsOverall Dimensions ModelWater Vapor a BY-PRODUCT of Unvented Room Heaters Unusually Tight ConstructionVentilation Air Ventilation Air From Inside Building Figure Ventilation Air From Inside BuildingOutdoors Ventilation Air From Outdoors FigureChecking Manifold Pressure Installing a New Main Gas CockGAS Supply Clearances See FigureCombustible Materials Mantel Clearances with Standard HoodPremium Vent-Free Fireplace Framing Dimensions Inches Planning InstallationFireplace Installation Instructions Fireplace FramingFireplace Installation Instructions Fireplace DimensionsLocating Fireplace Extended Hoods Installing HoodsHood Installation FinishingGAS Line Connection Placement of Glowing Embers and Lava Rock Placing Lava Rock in Front of Burner on Fireplace FloorOperation INSTRUCTIONS/FLAME Appearance All LogsMillivolt Valve lighting instructions Burner Instructions Pilot Flame Characteristics Incorrect Pilot Flame PatternRemote Receiver WiringCheck 750 Millivolt System Operation Appliance produces unwanted odors Gas odor even when control knob is in OFF positionHeater produces a whistling noise when main burner is lit Appliance shuts off during use. Pilot stays onDual Switch Electrical Wiring to Fireplace Receptacle Optional FBB5 Blower Installation Instructions WiringOptional Blower Installation Instructions Blower Motor Blower WheelsLK2 Accent Light Accessory MaintenanceParts List VALVE, NATHOW to Order Repair Parts Venturi GasketSEE-THROUGH Fireplace Parts View Peninsula Fireplace Parts View Frame Kits AccessoriesVariable Speed Control Kit Bottom Trim StripLouvers Accessory Description Model Numbers Accent Light KitExtended 4 Hoods Decorative Door KitsService Notes Empire Premium Vent-Free Fireplaces Empire Comfort Systems

VFP36PP32EP-2, VFP36SP32EP-2, VFP36SP32EN-2, VFP36PP32EN-2 specifications

Empire Comfort Systems offers a range of high-quality vent-free fireplaces, including the models VFP36SP32EN-2, VFP36SP32EP-2, VFP36PP32EP-2, and VFP36PP32EN-2. These models are engineered to provide both warmth and elegance, making them an exceptional choice for enhancing the ambiance of any living space.

One of the key features of these vent-free fireplaces is their impressive heating efficiency. They are designed to provide an optimal heat output without the need for a traditional flue or venting system, allowing homeowners to enjoy a cozy atmosphere without the associated installation and maintenance costs. With their high-efficiency gas burning systems, these fireplaces convert a significant portion of their fuel into heat, resulting in less energy waste and lower utility bills.

The VFP models are equipped with state-of-the-art flame technology, which produces realistic and visually appealing flames that mimic the beauty of a traditional wood-burning fire. The flame appearance can enhance any room’s aesthetics, creating a warm and inviting atmosphere that is perfect for gatherings or quiet evenings at home.

Another notable characteristic is the variety of styles available. The VFP36PP models feature a more modern, contemporary design, while the VFP36SP models have a traditional aesthetic that fits well with classic décor. This versatility in style allows homeowners to select a model that best suits their interior design preferences.

Safety is also a top priority with these fireplaces. They come with built-in safety features, including an automatic shut-off system that activates if the pilot light goes out, ensuring peace of mind for users. The models are also equipped with thermostat controls, allowing for easy temperature adjustments to maintain a comfortable environment.

In terms of fuel options, these vent-free fireplaces can operate on both natural gas and propane, providing flexibility based on the needs and availability of fuel sources. Moreover, they have a compact design, making them an excellent choice for smaller spaces or homes where traditional fireplaces may not be feasible.

In summary, Empire Comfort Systems' VFP36SP32EN-2, VFP36SP32EP-2, VFP36PP32EP-2, and VFP36PP32EN-2 models stand out for their efficiency, aesthetic appeal, safety features, and versatility. These vent-free fireplaces are an exceptional addition to any home, offering warmth and style with the convenience of easy installation and operation.