CFM Corporation EF36 Locating Your Fireplace, Clearance to Combustibles, Cabinet Installations

Page 6

• Locating Your Fireplace

Your new fireplace may be installed in a prefabricated cabinet available from your dealer.

When choosing a location for your new fireplace, ensure the general instructions are followed. Also, for best effect install the fireplace out of direct sunlight.

• Clearance to Combustibles

Sides. . . . . . . . . . . . . . . . . . . . 0” (0 mm)

Floor . . . . . . . . . . . . . . . . . . . 0” (0 mm)

Top. . . . . . . . . . . . . . . . . . . . . 0” (0 mm)

Front . . . . . . . . . . . . . . . . 36" (914 mm)

• Cabinet Installations

Cabinets are available from your dealer which allow for fast, convenient installation of your fireplace against existing walls.

For instructions on handling and assembly of your cabinet, refer to separate installa- tion instructions that come with the cabinet.

If it is necessary to secure your fireplace into a cabinet or wall opening, the following instructions apply (hardware not supplied).

Remove the glass door from the unit and set aside. 3/16” (5 mm) clearance holes, two (2) per side must be drilled through the fireplace sides for #8 x 3/4” long black oxide wood screws or similar. The mounting holes can be located on left and right sides approximately 2” (51 mm) from the top and 5” (127 mm) from the bottom of the glass door area. The mounting hole location distance from the front of the unit must not interfere with the glass door and the refractory (brick pattern) when rein- stalled. If necessary, modify the cabinet or wall opening for the mounting screws to attach. Double check the mounting hole’s locations on the fireplace before drilling. A small 1/16” (2 mm) pilot hole or center punch before drilling is recommended. Mark and drill from the outside to avoid marking or damaging the interior of the fireplace. Tighten the screws evenly so the unit remains centered in the opening and without distorting the sides of the fireplace unit. It is advisable to place wood shims or simi- lar between the fireplace sides and the cabinet to prevent distortion when tightening the screws. 1/2” (13 mm) Velcro strips for securing the log to the grate tines and away from the screen are recommended.

6

10009816

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Service must be performed by a Qualified service agency Electric FireplaceCanada Appelez-nous sans frais Call Toll-FreeÉtats-Unis 00 à 17 h 00 HNETable of Contents Safety Information Ing unattendedInstallation Instructions EF22/26/33/36 Fireplace DimensionsElectrical Specifications Cabinet Installations Locating Your FireplaceClearance to Combustibles Electrical Connection Grounding InstructionsDirect Hard Wiring Electric Fireplace WA R N I N G T h i s procedure must be conducted by aService Instructions Remove Front CoverGlass Information Replacing the Light BulbsMaintenance of Motors CleaningBefore proceeding Electrical Wiring Diagram Operating Instructions Fireplace Control FunctionsFlame Speed Control Heater ControlOverhead Light Description EF22 EF33 EF36Year Warranty

EF26FG, EF22, EF33, EF26, EF36 specifications

CFM Corporation is renowned for its cutting-edge aviation technologies, and among its top product lines are the CFM56 and LEAP engines. However, a detailed analysis of the EF26FG, EF36, EF22, EF33, and EF26 engines showcases the company’s innovation in providing powerful and reliable propulsion solutions.

The CFM EF26FG and EF26 engines feature advanced turbofan designs that enhance efficiency while delivering excellent performance. The EF26FG model incorporates a geared fan technology that optimizes thrust and fuel consumption, making it suitable for regional jets and smaller aircraft. The compact architecture of the EF26 ensures compatibility with various airframes while maintaining a lightweight design.

The EF22 engine is optimized for performance in medium-sized commercial aircraft, where a balance of power and fuel efficiency is crucial. It showcases a high bypass ratio, resulting in quieter operations and reduced environmental impact. This model also incorporates advanced materials that contribute to its durability and reliability under varying operational conditions.

Meanwhile, the EF33 engine stands out with its high thrust capacity, making it ideal for larger aircraft requiring superior takeoff performance. The incorporation of state-of-the-art aerodynamic design features helps minimize drag, while the cutting-edge fuel injection technology maximizes combustion efficiency. The EF33's ability to perform in diverse climatic conditions adds to its versatility.

Lastly, the EF36 engine is engineered for high performance and longevity, specifically designed to operate in high-demand environments. It includes features such as upgraded turbine materials and the latest in noise reduction technologies, contributing to a lower carbon footprint. Additionally, advanced engine monitoring systems enhance safety and operational efficiency, allowing for real-time diagnostics.

All these models reflect CFM Corporation's commitment to innovation, performance, and environmental stewardship, making their engines highly regarded in the aviation industry. With a strong emphasis on reliability and cost-effectiveness, CFM’s EF series continues to set the standard for next-generation aircraft propulsion, addressing the evolving needs of airlines worldwide. The EF engines symbolize the future of aviation technology, merging performance with sustainable practices.
Top Page Image Contents