Enviro EG40-070 owner manual End of the pipes and fittings, are

Page 20
Figure 24: Twist-Lock Connection

Initial Installation

QUALIFIED INSTALLERS ONLY

HORIZONTAL INSTALLATION:

1.Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance.

2.Direct vent pipe and fittings are designed with special twist-lock connections. Assemble the desired combination of black pipe and elbows to the appliance adapter with pipe seams oriented towards the wall or floor, as much out of view as possible.

Place a bead of Mil-Pac on the outer edge of the inner exhaust pipe (non-flared end). Place a bead of high temperature silicone on the male edge of the outer pipe. Push the pipe sections completely together, then twist-lock one section clockwise approximately 1⁄4 turn, until the two sections are fully locked. The female locking lugs will not be visible from the outside, on black pipe. They may be located by examining the inside of the female ends as shown in Figure 23.

Notes:

•

Twist-lock procedure: four (4)

 

indentations, located on the female

Female

end of the pipes and fittings, are

Locking

designed to slide straight onto the

Lugs

Sealant

male ends of adjacent pipes and

fittings, by orienting the four pipe

 

Male

indentations so they match and slide

Locking

into the four entry slots on the male

Lugs

 

end.

• Horizontal runs of vent pipe must be supported every three ft. Wall straps are available for this purpose, also

when running horizontal pipe minimum clearances to combustibles must be maintained; 2 inches (5.1 cm) at top, 11⁄2 inches (3.8 cm) at sides, 11⁄2 inches (3.8 cm) at bottom.

���

�������

���

�������

Figure 25: Wall Framing Hole for Horizontal Installation.

11/4"

 

(3.2cm)

 

Fold strap

Woodscrews

 

here

 

Sheet metal

 

screws

 

 

Wall Thimble

 

Strap

Figure 26: Installing Decorative Wall Thimble.

3. With the pipe attached to the stove in the correct location, mark the wall for a 10” (25.4 cm) x 10” (25.4 cm) square hole (refer to Figure 25). The center of the square hole should match the center line of the

horizontal pipe. Cut and frame the 10” (25.4 cm) x 10”

(25.4 cm) hole in the exterior wall where the vent will be terminated. If the wall being penetrated is constructed of non-combustible material i.e. masonry or concrete, a 7 inches (17.8 cm) hole is acceptable.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents EG40 DV Safety Precautions GeneralTable of Contents Codes And Approvals Vented GAS Fireplace Heater EG40 DV NG/LPGSpecifications EG40 Exterior DimensionsFor Your Safety Read Completely Before Operating Operating InstructionsThere is a separate venturies for each burner, see Figure Component Sound & ReasonMaintenance and Service Removing the DoorBurner is lined up Kit Parts List Conversion Kit InstallationMust be not visible Removing valve ScrewInitial Installation Qualified Installers onlyCommon Vertical Installation Do not interfere with the structural integrity of the walls Vent Termination Restrictions KIT Components Installation of Fireplace Horizontal Vent Kit Manufacturer Trade Name Nominal Sizes4DSC Vent restrictor ring End of the pipes and fittings, are Installing Vent Cap with Vinyl Siding Stand-Off Assemble the desired lengths of black pipe Use of Wall Straps Multi-Story Vent Pipe Installation Insulation33a-2002 Test Methods and the Resulting ITS/WH Must be connected to a grounding rod Must be bolted securely to the floorNatural Gas Propane Front Burner Rear BurnerManifold Pressure Min. Manifold PressureSecondary Installation Log PlacementRemove door to clean glass Trouble Shooting Problem Possible Cause SolutionParts List T. Nova Valve Convertible 50-1421Parts List Parts Diagram Chassis Parts Diagram Gas Tray Door Warranty To the DistributorInstallation Data Sheet

EG40-070 specifications

The Enviro EG40-070 is a state-of-the-art outdoor wood-burning furnace designed to provide an efficient and eco-friendly heating solution for residential and commercial spaces. As homeowners increasingly seek sustainable alternatives to traditional heating methods, the EG40-070 emerges as a formidable contender in the market.

One of the standout features of the Enviro EG40-070 is its high-efficiency heating capability. With an impressive thermal efficiency rating, this furnace ensures that a significant portion of the heat generated from the burning wood is effectively transferred to the water that circulates throughout the heating system. This efficiency reduces the amount of wood needed for heating, making it an environmentally friendly option.

The furnace is equipped with a robust and durable construction, designed to withstand the rigors of outdoor use. The heavy-duty steel body is resistant to corrosion and wear, ensuring longevity and minimal maintenance. Additionally, the large firebox allows for extended burn times, which means users can load it with wood and enjoy consistent heating for hours without the need for constant refueling.

Another significant characteristic of the Enviro EG40-070 is its advanced combustion technology. It features a secondary combustion system that maximizes the efficiency of the fuel being burned. By allowing for the recirculation of exhaust gases, this system ensures that virtually all the combustible materials are utilized, resulting in cleaner emissions. This not only benefits the environment but also contributes to better air quality.

The Enviro EG40-070 also boasts a user-friendly design, complete with easy-access doors for loading fuel and cleaning. The integrated digital control system allows for precise regulation of the temperature and heat output, providing users with a customizable heating experience. Furthermore, the unit is compatible with various heating systems, including forced air and hydronic systems, making it versatile for different applications.

For safety, the furnace incorporates several safety features, including low water protection and an automatic shut-off function. These features are crucial in preventing overheating and ensuring safe operation, giving homeowners peace of mind.

In summary, the Enviro EG40-070 is a powerful outdoor wood-burning furnace that combines efficiency, durability, and functionality. Its advanced combustion technologies and user-friendly design make it a suitable choice for those looking to embrace a sustainable heating solution without compromising on performance or safety.
Top Page Image Contents