Removing valve screw | Enviro Ascot instruction

Figure 10: O-ring on valve screw.

Maintenance And Service

7.Convert the SIT gas valve:

a)Remove the black protection cap from the HI/LO knob by hand shown in Figure 7.

b)Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 8), rotate it counter-clockwise until it is free and extract it.

c)Check that the screw is clean and if necessary remove dirt.

d)Flip the screw (refer to Figure 9).

e)Using the Allen wrench as shown in Figure 8, rotate the screw clockwise until a torque of 9 inch lbs. WARNING! Do not over tighten the screw. It is recommended that you grip the wrench by the short side.

f)Verify that if the conversion is from NG to LPG, the screw must be re-assembled with the red o- ring visible (refer to Figure 10). If the conversion is from LPG to NG, the red o-ring of the screw must be not visible.

Figure 8: Removing valve screw.

Figure 9: Flip valve

screw.

g)Re-attach the black protection cap that was removed in step a (Figure 7).

8.Reinstall the burner, brick panels, log set, embers, and glass door.

Also refer to SECONDARY INSTALLATION - INSTALLING LOG SET AND EMBERS. When

re-installing the burner, ensure that the burner to pilot hood relationship

is similar to what is shown in Figure 11. On some units you will need to pay special attention when installing the burner that the venturi adjustment rod is properly installed into the venturi adjustment piece welded to the burner venturi tube

9.Reconnect the main gas line if it was disconnected and open the shut-off valve at the gas line to the unit.

10.Use a small brush to apply a warm soapy water solution to all gas connections (use a half dish soap and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by using an approved pipe thread sealant or approved Teflon tape. NEVER USE AN OPEN FLAME WHEN TESTING FOR LEAKS.

11.Reconnect the electrical power to the unit.

Figure 11. Ignitor

assembly beside the

burner.

12.Relight the main burner in both the “HI” and “LO” positions to verify proper burner ignition and operation and proper flame appearance. Also refer to SECONDARY INSTALLATION - LOG SET AND EMBERS INSTALLATION for a flame appearance picture.

13.MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit has been converted to a different fuel type.

Ascot specifications

Enviro Ascot is a cutting-edge innovation in sustainable living, a forward-thinking development that marries modern architecture with eco-friendly technologies. Nestled in a prime location, Enviro Ascot is designed to minimize environmental impact while maximizing the quality of life for its residents. The project stands as a testament to how urban spaces can be designed sustainably without compromising on aesthetics or functionality.

One of the main features of Enviro Ascot is its emphasis on energy efficiency. The buildings are equipped with state-of-the-art insulation materials and energy-efficient windows that help to reduce heat loss in winter and heat gain in summer. Solar panels placed on rooftops harness renewable energy, providing a significant portion of the electricity needs for the community. This not only lowers utility costs but also significantly reduces the carbon footprint of the development.

Water conservation is another hallmark of Enviro Ascot. The community features a rainwater harvesting system that collects and stores rainwater for use in irrigation and other non-potable applications. This initiative not only conserves precious water resources but also alleviates pressure on local water supply systems. Additionally, drought-resistant landscaping has been incorporated into the design, ensuring that the green spaces remain vibrant even during dry spells.

In terms of transportation, Enviro Ascot promotes a car-free lifestyle with extensive biking and walking paths interwoven throughout the community. Charging stations for electric vehicles are available at strategic locations, encouraging the use of eco-friendly transportation. The design is pedestrian-centric, making it easy for residents to access essential services, parks, and amenities without the need for a car.

Furthermore, the community boasts smart home technologies that enhance convenience and sustainability. Homes are outfitted with smart thermostats, energy-monitoring systems, and home automation features, allowing residents to optimize their energy use seamlessly. Through a centralized app, residents can monitor energy consumption, schedule heating and cooling, and even control lighting and security systems from their smartphones.

The architectural design of Enviro Ascot reflects a contemporary aesthetic while being practical. Natural materials and earthy color palettes integrate the buildings into the surrounding environment, creating a harmonious blend with nature. Green roofs and living walls add to the biodiversity of the area, providing habitats for various species and improving air quality.

In conclusion, Enviro Ascot is not just a residential development; it is a vision for the future of sustainable living. With its commitment to energy efficiency, water conservation, and innovative technologies, it stands as a model for environmentally responsible urban design. Residents of Enviro Ascot enjoy a lifestyle that is both modern and eco-conscious, paving the way for a sustainable future.