GAS Line Connection, To Test Valve Pressures

Initial Installation

GAS LINE CONNECTION AND TESTING:

WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance.

GAS LINE CONNECTION

•This stove is equipped with a certified flexible pipe located on the right side of the unit terminating in a 3⁄8” male NPT fitting. Consult your local authorities codes or the CAN/CGA B 149 (1 or 2) installation code in Canada, or in the USA gas installations follow either local codes or the current edition of the National Fuel Gas Code ANSI Z223.1.

•The efficiency rating of this appliance is a product thermal efficiency rating determined under continuous operating conditions and was determined independently of any installed system.

The appliance and its shutoff valves must be disconnected from the gas supply piping system during any pressure testing where the pressure exceeds 1⁄2 PSIG (3.45 KPa) or damage will occur to the valve.

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1⁄2 psig (3.45 KPa).

Always check for gas leaks with a soap and water solution after completing the required pressure test.

TO TEST VALVE PRESSURES

		��		��
		��		��
		��		��
		��
TP TH		OUT	IN
TP TH
TP	H	O
TP	I	L	OF
	I		OF
			F
			P
TH			I
			L
			T	O
			T	O
			NO
T	P
T	I
OL
��	��		��
��	��		��

Figure 45: Fully Labeled Gas Valve.

The pressure taps are located on the left side of the valve

•Turn set screw 1 turn counter clockwise to loosen,

•Place 5/16” (8 mm) I.D. hose over pressure tap system.

•Check pressures using a manometer.

•When finished, release pressure, remove hose & tighten set screw.

Table 6: Pressure and BTU Information.

	Natural Gas	Propane
Main Burner	#48 DMS	#57 DMS
Manifold Pressure	3.8” W.C. / 0.95KPa	11.0” W.C. / 2.7KPa

Min. Manifold Pressure	1.1” W.C. / 0.27KPa	2.7” W.C. / 0.67KPa

Max Supply Pressure	7.0” W.C. / 1.74KPa	13.0” W.C. / 3.28KPa

Min. Supply Pressure	5” W.C. / 1.24KPa	12.0” W.C. / 2.98KPa

Max BTU/hr Input	17,000 BTU/hr / 4.98KW	16,000 BTU/hr / 4.68KW

Min. BTU/hr Input	10,000 BTU/hr / 2.93KW	8,000 BTU/hr / 2.34KW

NEVER USE AN OPEN FLAME FOR LEAK TESTING.

Ascot specifications

Enviro Ascot is a cutting-edge innovation in sustainable living, a forward-thinking development that marries modern architecture with eco-friendly technologies. Nestled in a prime location, Enviro Ascot is designed to minimize environmental impact while maximizing the quality of life for its residents. The project stands as a testament to how urban spaces can be designed sustainably without compromising on aesthetics or functionality.

One of the main features of Enviro Ascot is its emphasis on energy efficiency. The buildings are equipped with state-of-the-art insulation materials and energy-efficient windows that help to reduce heat loss in winter and heat gain in summer. Solar panels placed on rooftops harness renewable energy, providing a significant portion of the electricity needs for the community. This not only lowers utility costs but also significantly reduces the carbon footprint of the development.

Water conservation is another hallmark of Enviro Ascot. The community features a rainwater harvesting system that collects and stores rainwater for use in irrigation and other non-potable applications. This initiative not only conserves precious water resources but also alleviates pressure on local water supply systems. Additionally, drought-resistant landscaping has been incorporated into the design, ensuring that the green spaces remain vibrant even during dry spells.

In terms of transportation, Enviro Ascot promotes a car-free lifestyle with extensive biking and walking paths interwoven throughout the community. Charging stations for electric vehicles are available at strategic locations, encouraging the use of eco-friendly transportation. The design is pedestrian-centric, making it easy for residents to access essential services, parks, and amenities without the need for a car.

Furthermore, the community boasts smart home technologies that enhance convenience and sustainability. Homes are outfitted with smart thermostats, energy-monitoring systems, and home automation features, allowing residents to optimize their energy use seamlessly. Through a centralized app, residents can monitor energy consumption, schedule heating and cooling, and even control lighting and security systems from their smartphones.

The architectural design of Enviro Ascot reflects a contemporary aesthetic while being practical. Natural materials and earthy color palettes integrate the buildings into the surrounding environment, creating a harmonious blend with nature. Green roofs and living walls add to the biodiversity of the area, providing habitats for various species and improving air quality.

In conclusion, Enviro Ascot is not just a residential development; it is a vision for the future of sustainable living. With its commitment to energy efficiency, water conservation, and innovative technologies, it stands as a model for environmentally responsible urban design. Residents of Enviro Ascot enjoy a lifestyle that is both modern and eco-conscious, paving the way for a sustainable future.