FireplaceXtrordinair 36A-BI Protecting the Gold on the Fireplace Xtrordinair, Acid Wash Warning

Page 6

PROTECTING THE GOLD ON THE FIREPLACE XTRORDINAIR

Gold is the very best material available for plating fireplace fronts, but it is not indestructible. The most common complaint with any plated surface on a wood burning appliance is discoloration. This can only be caused by heat or chemicals. The discoloration is permanent and cannot be removed. The following warnings will help you protect the shine in the gold plating.

NOTE: IF YOU ARE INSTALLING YOUR FIREPLACE XTRORDINAIR INTO A NEW MASONRY OR BLOCK-IN FIREPLACE, YOU SHOULD READ THE FOLLOWING WARNING ON ACID WASH:

Acid Wash Warning:

In the past gold faceplates and/or doors have become severely tarnished as a direct result of acid wash that has not been properly neutralized on masonry fireplaces. This condition occurs when the masonry fireplace is newly constructed and muriatic acid is used to remove excess mortar. If the mason does not adequately neutralize this muriatic acid with ammonia and water, the acid will be left on the brick. Whenever the fireplace is heated, either from a fire or from room heat, acid vapors will be released from the brick. These vapors are extremely corrosive and will attack any metal surface in the immediate area of the fireplace. Gold plated surfaces will develop a cloudy film.

Replacement of the faceplate and/or doors WILL NOT CURE THIS PROBLEM! The correct repair is to have the masonry contractor come out to the house and wash down the entire fireplace face to neutralize this acid condition. If this is a new home, the repair should be covered under warranty by the home builder. If this is an older home, the consumer may have some recourse from the seller. We stress that this condition is not a defect in the manufacture of the plating, but an acid problem with the brick or stone of the fireplace face.

You can test your brickwork for improper neutralization by using a spa or pool test strip which is available at spa and pool stores. Apply one drop of water to your brick and touch the test strip to the brick (Refer to instructions on the packaging when reading the test strip). If the strip shows a high acid content you will need to take steps to properly neutralize your brick. Please be aware that the warranty for your Fireplace Xtrordinair will not cover damage to the plating as a result of an improperly neutralized acid wash.

Heat Warning:

ACID

WASH

New Masonry

Gold plating is inherently resistant to heat and will not discolor under normal conditions. However, there are some conditions that may damage the gold surfaces due to excessive heat you should be aware of.

The Fireplace Xtrordinair was designed and safety tested to withstand a full load of normal wood burning at the highest burn rate. However, do not use the fireplace continuously at this high-temperature level. Be careful with hot-burning wood (dense wood or wood that is in small pieces). If any part of the interior of the fireplace is glowing red, the fireplace is over- fired and should be turned to a lower burn rate and allowed to cool down. Also be aware of excessive temperatures due to a power outage shutting off the blower. With the blower disconnected from power, the heat from the fireplace will build up quicker and not dissipate as well. During power outages, do not run the fireplace at high burn rate settings.

Page 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Page Safety Precautions Table of Contents Features and Specifications 36A-BIChimney Size and Proper Draft Protecting the Gold on the Fireplace Xtrordinair Acid Wash WarningHeat Warning Arched Face Operating Your ApplianceLocation and Use of Controls Square FaceBurning Procedure Operating Your ApplianceMaintaining Catalytic Light-Off Catalytic LIGHT-OFFApproximate Combustion AIR Control Settings Burning Your Appliance EfficientlyDaily Use of Your Appliance At 20% moisture content All values are approximate WoodSeasoning Wood Solar Wood Dryer Typical Wood Shed Storing WoodLeads Safety in Operation Maintenance Instructions Care and MaintenanceMaintenance Schedule Cleaning of Gold Plated SurfacesDoor and Window Gasket Inspection Glass CleaningDoor Latch Inspection and Adjustment LubricateCheck for Creosote Catalytic Combustor Inspection & Cleaning Check for CreosoteTo prevent creosote accumulation Catalytic Combustor Inspection & Cleaning Firebox Inspection and CleaningAppliance TOUCH-UP Chimney System Cleaning Blower CleaningBefore Calling for Service Replacement Parts and Removal Instructions Replacement Parts Part Name Part Number Part DescriptionRemoval Instructions Removing and Replacing the Glass Removing and Replacing the Door GasketRemoving and Replacing the Firebricks Removing the Side FirebricksDimensions of Firebrick Brick # Removing and Replacing the Catalytic CombustorCombustor Assembly Year Warranty Xtrordinair applianceSafety Label 36A-BI 36A-ZC

36A-ZC, 36A-BI specifications

FireplaceXtrordinair 36A-ZC and 36A-BI are prominent models in the realm of modern gas fireplaces, providing both warmth and aesthetic appeal to any living space. These fireplaces are known for their exceptional design, energy efficiency, and technological features that enhance the overall user experience.

One of the standout characteristics of the 36A-ZC and 36A-BI is their large viewing area. The expansive glass front offers an unobstructed view of the vibrant flames, creating an inviting ambiance. The clean, linear design further enhances the visual appeal, making it a stunning focal point in any room. Both models are available in multiple finish options, allowing homeowners to customize the look to blend seamlessly with their interior decor.

In terms of performance, the FireplaceXtrordinair 36A-ZC and 36A-BI are equipped with advanced heating technologies. They feature a powerful heating capacity, which ensures that even larger spaces can be warmed efficiently. The models utilize a high-efficiency burner system that maximizes heat output while minimizing gas consumption. This not only contributes to energy savings but also makes the fireplaces environmentally friendly.

The 36A-ZC is designed for traditional wall installations, whereas the 36A-BI is specifically created for built-in applications. This provides flexibility for homeowners, as they can choose the configuration that best suits their space. Both models include innovative features such as adjustable flame height and customizable media options, including various ceramic stones or logs, enabling users to create their desired aesthetic.

Control is another key aspect of the FireplaceXtrordinair 36A-ZC and 36A-BI. They come equipped with a user-friendly remote control, allowing for easy operation from afar. Additionally, they feature electronic ignition for easy start-up, and the option for venting ensures that the installation can be adapted to various home environments.

Safety is paramount with these models, as they include built-in safety features such as flame sensing technology and a glass safety screen. This ensures peace of mind when using the fireplace, especially in homes with children or pets.

Overall, FireplaceXtrordinair 36A-ZC and 36A-BI represent a fusion of style and technology, providing warmth and elegance to any setting. Their superior efficiency, aesthetic versatility, and user-friendly features make them a premier choice for modern homeowners looking to enhance their living spaces.
Top Page Image Contents