FireplaceXtrordinair 36A-ZC, 36A-BI Catalytic Combustor Inspection & Cleaning, Appliance TOUCH-UP

Page 21

CARE AND MAINTENANCE (Continued)

CATALYTIC COMBUSTOR INSPECTION & CLEANING (Continued)

mode). Use the following three steps to determine your catalytic combustor's performance:

Step 1. Light fireplace. Let the fireplace reach operating temperature.

Step 2. With smoke routed through the catalyst (By-pass closed), go outside and observe the emissions leaving the chimney.

Step 3. Open the by-pass and again observe the emissions leaving the chimney. You should see significantly more smoke when the exhaust is not routed through the combustor (by-pass mode). Be careful not to confuse smoke with steam from wet wood.

If you can't operate with combustor temperatures in excess of 500 degrees F. there will be excessive smoke leaving the chimney. You should check to make sure that your firewood is dry and seasoned. Wet or green wood will cause the combustor to not light off until the moisture is evaporated. Because the combustor is not working under these conditions, excessive amounts of creosote can be deposited in the chimney system.

Using A Temperature Probe To Check The Catalytic Combustor

Visual inspection of the catalytic combustor should provide a suitable method for monitoring this component in your fireplace. If a more detailed monitoring process is desired, a temperature probe can be used to monitor the fireplace while it is in operation.

Your Fireplace Xtrordinair is equipped with a hook-up for a temperature probe to monitor combustor operation. There is a two prong connector plug behind the blower speed control for a Condar Temp-meter (Model 9-85). To attach the Temp-meter, attach a matching connector plug or splice the wires coming from the Temp-meter to the two prong connector plug behind the blower speed control. A properly functioning combustor typically maintains temperatures in excess of 500 to 1000 degrees F. If combustor temperatures are not in excess of 500 degrees F. refer to the section "Visual Inspection & Cleaning Of The Catalytic Combustor" in this owner's manual to determine the problem.

FIREBOX INSPECTION AND CLEANING

At the end of each heating season, remove all of the ash inside the firebox and check for any scale that may have built up during the heating season. Remove any scale from the inside of the firebox with a wire brush or scraper. With a flashlight check to see that all of the firebrick lining the firebox is in good condition. If any of the firebrick is cracked or broken, follow the directions in the section titled "REPLACEMENT PARTS AND REMOVAL INSTRUCTIONS" for removal and replacement of any damaged firebrick.

APPLIANCE TOUCH-UP

The outside of the appliance can be touched up using high temperature "Forrest Stove-Brite" paint, available at your dealer. This will improve the looks of your appliance, but is not necessary. To touch up paint, first sand the area to be painted with 120 grit sandpaper, clean it with water only, and dry with a clean cloth. Paint using light covering coats. The newly painted area will appear darker until the paint goes through the curing process.

Touch-Up

P a i n t

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Page Safety Precautions Table of Contents 36A-BI Features and SpecificationsChimney Size and Proper Draft Protecting the Gold on the Fireplace Xtrordinair Acid Wash WarningHeat Warning Location and Use of Controls Operating Your ApplianceArched Face Square FaceOperating Your Appliance Burning ProcedureCatalytic LIGHT-OFF Maintaining Catalytic Light-OffApproximate Combustion AIR Control Settings Burning Your Appliance EfficientlyDaily Use of Your Appliance Wood At 20% moisture content All values are approximateSeasoning Wood Solar Wood Dryer Storing Wood Typical Wood ShedLeads Safety in Operation Maintenance Schedule Care and MaintenanceMaintenance Instructions Cleaning of Gold Plated SurfacesDoor Latch Inspection and Adjustment Glass CleaningDoor and Window Gasket Inspection LubricateCheck for Creosote Catalytic Combustor Inspection & Cleaning Check for CreosoteTo prevent creosote accumulation Catalytic Combustor Inspection & Cleaning Firebox Inspection and CleaningAppliance TOUCH-UP Blower Cleaning Chimney System CleaningBefore Calling for Service Replacement Parts and Removal Instructions Replacement Parts Part Name Part Number Part DescriptionRemoval Instructions Removing and Replacing the Door Gasket Removing and Replacing the GlassRemoving the Side Firebricks Removing and Replacing the FirebricksRemoving and Replacing the Catalytic Combustor Dimensions of Firebrick Brick #Combustor Assembly Xtrordinair appliance Year Warranty36A-BI 36A-ZC Safety Label

36A-ZC, 36A-BI specifications

FireplaceXtrordinair 36A-ZC and 36A-BI are prominent models in the realm of modern gas fireplaces, providing both warmth and aesthetic appeal to any living space. These fireplaces are known for their exceptional design, energy efficiency, and technological features that enhance the overall user experience.

One of the standout characteristics of the 36A-ZC and 36A-BI is their large viewing area. The expansive glass front offers an unobstructed view of the vibrant flames, creating an inviting ambiance. The clean, linear design further enhances the visual appeal, making it a stunning focal point in any room. Both models are available in multiple finish options, allowing homeowners to customize the look to blend seamlessly with their interior decor.

In terms of performance, the FireplaceXtrordinair 36A-ZC and 36A-BI are equipped with advanced heating technologies. They feature a powerful heating capacity, which ensures that even larger spaces can be warmed efficiently. The models utilize a high-efficiency burner system that maximizes heat output while minimizing gas consumption. This not only contributes to energy savings but also makes the fireplaces environmentally friendly.

The 36A-ZC is designed for traditional wall installations, whereas the 36A-BI is specifically created for built-in applications. This provides flexibility for homeowners, as they can choose the configuration that best suits their space. Both models include innovative features such as adjustable flame height and customizable media options, including various ceramic stones or logs, enabling users to create their desired aesthetic.

Control is another key aspect of the FireplaceXtrordinair 36A-ZC and 36A-BI. They come equipped with a user-friendly remote control, allowing for easy operation from afar. Additionally, they feature electronic ignition for easy start-up, and the option for venting ensures that the installation can be adapted to various home environments.

Safety is paramount with these models, as they include built-in safety features such as flame sensing technology and a glass safety screen. This ensures peace of mind when using the fireplace, especially in homes with children or pets.

Overall, FireplaceXtrordinair 36A-ZC and 36A-BI represent a fusion of style and technology, providing warmth and elegance to any setting. Their superior efficiency, aesthetic versatility, and user-friendly features make them a premier choice for modern homeowners looking to enhance their living spaces.
Top Page Image Contents