Lucent Technologies MPE-33R warranty Important Safety and Warniing Information

Page 2

IMPORTANT SAFETY AND WARNIING INFORMATION

read THIS MANUAL IN ITS ENTIRETY and understand these Rules to follow for safety.

WARNING

If the information in this manual is not followed exactly, an elec- trical shock or fire may result causing property damage, per- sonal injury or loss of life.

IMPORTANT

Before starting your fireplace installation, read this instal- lation and operation manual very carefully to ensure you understand it completely and in entirety. Failure to follow these instructions may result in a pos- sible electric shock, fire hazard and/or injury or property damage and will void the warranty.

CAUTION

This appliance is mounted on rubber feet. The purpose of these feet is to ensure adequate air circulation beneath the fireplace. Do not remove these feet. Do not install the fireplace directly onto a carpet, rug, furniture or similar surfaces, which could hinder or block the airflow.

CAUTION

Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left oper- ating and unattended.

IMPORTANT

These fireplaces are designed as supplemental heaters. There- fore, it is advisable to have an alternate heat source when installed in a dwelling.

IMPORTANT

Cold climate installation recom- mendation: when installing this fireplace against a non-insulated exterior wall or chase, it is mandatory that the outer walls be insulated to conform to appli- cable insulation codes.

WARNING

To prevent contact with sag- ging or loose insulation, the appliance must not be installed againstvaporbarriersorexposed insulation. Localized overheat- ing could occur and a fire could result. Insulation and a vapor barrier should be placed a minimum of 2 inches from the appliance.

To prevent a possible fire, do not block air intakes or exhausts in any way. Do not use near soft surfaces, like a pillow, where openings may become blocked.

THIS APPLIANCE MAY BECOME HOT WHEN IN USE. TO AVOID BURNS, DO NOT LET BARE SKIN TOUCH HOT SUR- FACES. KEEP COMBUSTIBLE MATERI- ALS, SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS, CLOTHES AND CURTAINS AT LEAST 3 FEET (1 METER) FROM THE FRONT OF THIS APPLI- ANCE.

DO NOT OPERATE ANY HEATER WITH DAMAGED WIRING OR CONNECTORS, OR AFTER THE APPLIANCE MALFUNC- TIONS, OR IF IT HAS BEEN DROPPED OR DAMAGED IN ANY WAY.

ANY REPAIRS TO THIS FIREPLACE SHOULD BE PERFORMED BY A QUALI- FIED SERVICE TECHNICIAN.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

UNDER NO CIRCUMSTANCES SHOULD THIS FIREPLACE BE MODIFIED. PARTS HAVING TO BE REMOVED FOR SERVIC- ING MUST BE REPLACED PRIOR TO OPERATING THE FIREPLACE AGAIN.

DO NOT USE THIS APPLIANCE OUT- DOORS. DO NOT EXPOSE FIREPLACE TO THE ELEMENTS (SUCH AS RAIN, ETC.).

THIS APPLIANCE IS NOT INTENDED FOR USE IN BATHROOMS, LAUNDRY AREAS OR SIMILAR INDOOR LOCA- TIONS. NEVER LOCATE THIS APPLI- ANCE WHERE IT COULD FALL INTO A BATHTUB OR OTHER WATER CON- TAINER.

DO NOT RUN ELECTRICAL WIRING OR POWER CORD UNDER CARPETING. OR COVER WITH THROW RUGS, RUNNERS OR SIMILAR MATERIALS.

FOR 120 VAC POWER CORD AVOID THE USE OF AN EXTENSION CORD BECAUSE THE EXTENSION CORD MAY OVERHEAT AND CAUSE A RISK OF FIRE. HOW- EVER, IF YOU HAVE TO USE AN EXTEN- SION CORD, THE CORD SHALL BE NO. 14 AWG MINIMUM SIZE AND RATED NOT LESS THAN 1800 WATTS, 15 AMPS. THE EXTENSION CORD MUST BE A THREE CONDUCTOR SHEATH CABLE WITH GROUNDING TYPE PLUG AND CORD CONNECTION.

THIS APPLIANCE HAS HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE USED OR STORED.

THIS FIREPLACE SHOULD NOT BE USED AS A DRYING RACK FOR CLOTHING, NOR SHOULD CHRISTMAS STOCKINGS OR OTHER DECORATIONS BE HUNG NEAR IT.

USE THIS APPLIANCE ONLY AS DESCRIBED IN THIS MANUAL. ANY OTHER USE IS NOT RECOMMENDED BY THE MANUFACTURER AND MAY CAUSE A FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS.

IF APPLIANCE IS TO BE DISCON- NECTED, TURN OFF CONTROLS FIRST.

DO NOT INSERT OR ALLOW FOREIGN OBJECTS TO ENTER ANY VENTILATION OR EXHAUST OPENING, AS THIS MAY CAUSE AN ELECTRIC SHOCK, FIRE, OR DAMAGE TO THE APPLIANCE.

SAVE THESE INSTRUCTIONS.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Report # C1482763 Electric Fireplace 850,032M REV. E 04/2007Do not Block Airflow AT the Bottom AIR Intakes Important Safety and Warniing Information Congratulations Left Side Framing SpecificationsFireplace specifications Top ViewPRE-INSTALLATION Manual control Panel Final FinishingBREAK-IN Period Manual Control Panel OperationRemote Control Operation HEATER/BLOWER Replacement PROCE- Dure MaintenanceCleaning the Glass Enclosure Panel optional kit Brick Panel Removal ProcedureAcess bulbs as follows Bulb Replacement ProcedureReplacing Light Bulbs Ember BedGround 120 v 1600 w Wiring Diagram 120 voltWiring 120 volt Ground 240 v 3000 w Wiring 240 voltGround GroundOptional kits, see Wall Thermostat & Wall Switch Wiring DiagramsInside Outside Inside OutsideBlack White Wall Thermostat Wiring 24 VACWall Thermostat White Left Side FireplaceRed Wire the wall switch prior to installing the fireplaceWall Switch Wiring 24 VAC Action Symptom Possible CausesCorrective Action Replacement Parts Description MPE-33R Cat. No QtyReplacement Parts component diagrams MPE-33R 154Wall Thermostat Accessory ComponentsWall Switch Kit Trim KitPage West Taft Avenue Orange, CA

MPE-33R specifications

Lucent Technologies MPE-33R is a versatile and robust platform designed for telecommunications and networking solutions. Known for its high performance, this multiprotocol platform is integral in facilitating seamless data transmission across various global networks. The MPE-33R stands out in the telecommunications landscape due to its compatibility with a wide range of protocols, making it ideal for service providers aiming to deliver diverse services.

One of the main features of the MPE-33R is its ability to support multiple network protocols. This flexibility is essential for operators who need to handle different types of traffic, such as voice, video, and data, all within one system. The platform is engineered to be protocol-agnostic, which means it can adapt to emerging communication standards, ensuring longevity and relevance in a fast-evolving tech environment.

Another significant characteristic of the MPE-33R is its modular architecture. This design allows for easy upgrades and scaling, enabling operators to expand their capabilities without overhauling their entire infrastructure. Users can add or remove modules to accommodate changes in demand or to integrate new technologies, making it an economical choice for businesses that anticipate growth.

The MPE-33R also supports advanced Quality of Service (QoS) features, essential for maintaining high standards in service delivery. With QoS, operators can prioritize traffic, ensuring that critical applications receive the bandwidth they require, while less critical transmissions do not disrupt overall network performance. This is particularly crucial in environments where real-time communication is vital, such as in VoIP services.

Additionally, the platform incorporates state-of-the-art security features. With the increasing focus on cybersecurity in telecommunications, the MPE-33R includes encryption and authentication protocols to protect data and ensure secure communications. Operators can, therefore, provide peace of mind to their users, knowing that their information is safeguarded against potential threats.

In summary, Lucent Technologies MPE-33R is characterized by its versatility, modularity, advanced QoS capabilities, and robust security features. This multiprotocol platform effectively meets the demands of modern telecommunications, making it an invaluable asset for service providers looking to enhance their network offerings while adapting to the shifting technological landscape. As the need for integrated communication solutions continues to grow, the MPE-33R positions itself as a reliable and future-proof option for businesses worldwide.
Top Page Image Contents