Lucent Technologies MPE-33R warranty Pre-Installation

Page 5

Fireplace specifications

Cat. No. H3427

Model: MPE-33R

Description: Merit Plus Electric Fireplace, 33” Radiant

Shipping Weight: 81 lb.'s (36.75 KG)

Packaging:

41” x 17 3/4” x 33 1/2”

(1040 mm x 451 mm x 850 mm)

14.1cu. ft.

Power Requirements: (120 Volt, 60 Hz.)

Rated Wattage - 1600 Watts Amperage - 13.33 Amps

(240 Volt, 60 Hz.)

Rated Wattage - 3000 Watts Amperage - 12.5 Amps

Blower CFM: 83 CFM

(120 V): 5,461 BTU/HR

(240 V): 10,239 BTU/HR

Minimum Clearances to Combus- tibles

This appliance is an electric fireplace designed to be framed in with combustible materials (up to the edge of the appliance). A drywall lip at the top of the fireplace and 4 nailing flanges on the sides of the appliance is provided to facilitate installation.

 

Clearances

 

 

 

Sides

 

0 inches - 0 mm

Floor

 

0 inches - 0 mm

 

 

 

Top

 

0 inches - 0 mm

Table 2

 

 

 

 

 

Mantel Clearance: Combustible and Non-com- bustible mantels may be installed at any height above the top of the face of fireplace.

Hearth Protection: A hearth is not mandatory, but it is recommended for aesthetic purposes. Secure the hearth extension to the floor to prevent possible shifting. Do no block the air- flow beneath the appliance (read the following WARNING).

PRE-INSTALLATION

Before You Start

Check appliance for any concealed damage.

Detailed Installation Steps

1.Complete the framing opening to the dimen- sions specified in Figure 2.

2.Prepare the connections to power source: 120 Volt Connections - Locate the power cord on the left side of the unit and connect it to the outlet installed during the framing (see Figure 2). Verify that the power to the receptacle is off.

Hard wired installation:

Ensure that there is a minimum of 8" of the service cable for connection to the junction box on the fireplace.

-Loosen four screws to remove the junction box cover plate.

-Disconnect and remove the 120 Volt power cord from the fireplace wires.

-Position the fireplace into the framed-in opening. Attach fireplace to frame using nailing flanges provided.

-Complete the wiring to the fireplace as shown on Page 10.

-Place all wire connectors inside the junction box.

-Attach junction box cover plate with four screws.

240 Volt Connections - Ensure that there is a minimum of 8" of the service cable for connection to the junction box on the fireplace.

-Loosen four screws to remove the junction box cover plate.

-Disconnect and remove the 120 Volt power cord from the fireplace wires.

-Position the fireplace into the framed-in opening. Attach fireplace to frame using nailing flanges provided.

-Complete the wiring to the fireplace as shown on Page 11.

-Place all wire connectors inside the junction box.

-Attach junction box cover plate with four screws.

The fireplace wires L1, L2, N, N1, N2 and G are attached to the rear of the junction box cable clamp for easy access.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

3.Wire a dedicated, properly fused circuit with an Amp rating for the appropriate voltage (120 V - 15 Amps or 240 V - 20 Amps). A dedicated circuit is required to prevent overloading a house circuit in cases of having multiple appliances on the same circuit. Use an outlet that is protected by a ground fault circuit interrupter where required by electrical code.

4.(If applicable) Make wall mount wall switch or wall thermostat connections as outlined on Pages 11 & 12.

5.Perform a function test. See Manual Control Panel Operation on Page 6 and Remote Control Operation on Page 7.

Electrical connections

Refer to the electrical diagrams on Pages 10

to 14.

WARNING

Electrical wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to individuals.

IMPORTANT

Any electrical re-wiring of this appliance must be done by a qualified electrician.

WARNING

Do not use this fireplace if any part of it has been underwater. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Report # C1482763 Electric Fireplace 850,032M REV. E 04/2007Do not Block Airflow AT the Bottom AIR Intakes Important Safety and Warniing Information Congratulations Fireplace specifications Framing SpecificationsLeft Side Top ViewPRE-INSTALLATION BREAK-IN Period Final FinishingManual control Panel Manual Control Panel OperationRemote Control Operation Cleaning the Glass Enclosure Panel optional kit MaintenanceHEATER/BLOWER Replacement PROCE- Dure Brick Panel Removal ProcedureReplacing Light Bulbs Bulb Replacement ProcedureAcess bulbs as follows Ember BedGround 120 v 1600 w Wiring Diagram 120 voltWiring 120 volt Ground Wiring 240 voltGround 240 v 3000 w GroundInside Outside Wall Thermostat & Wall Switch Wiring DiagramsOptional kits, see Inside OutsideWall Thermostat Wall Thermostat Wiring 24 VACBlack White White Left Side FireplaceRed Wire the wall switch prior to installing the fireplaceWall Switch Wiring 24 VAC Action Symptom Possible CausesCorrective Action Description MPE-33R Cat. No Qty Replacement Parts154 Replacement Parts component diagrams MPE-33RWall Switch Kit Accessory ComponentsWall Thermostat Trim KitPage West Taft Avenue Orange, CA

MPE-33R specifications

Lucent Technologies MPE-33R is a versatile and robust platform designed for telecommunications and networking solutions. Known for its high performance, this multiprotocol platform is integral in facilitating seamless data transmission across various global networks. The MPE-33R stands out in the telecommunications landscape due to its compatibility with a wide range of protocols, making it ideal for service providers aiming to deliver diverse services.

One of the main features of the MPE-33R is its ability to support multiple network protocols. This flexibility is essential for operators who need to handle different types of traffic, such as voice, video, and data, all within one system. The platform is engineered to be protocol-agnostic, which means it can adapt to emerging communication standards, ensuring longevity and relevance in a fast-evolving tech environment.

Another significant characteristic of the MPE-33R is its modular architecture. This design allows for easy upgrades and scaling, enabling operators to expand their capabilities without overhauling their entire infrastructure. Users can add or remove modules to accommodate changes in demand or to integrate new technologies, making it an economical choice for businesses that anticipate growth.

The MPE-33R also supports advanced Quality of Service (QoS) features, essential for maintaining high standards in service delivery. With QoS, operators can prioritize traffic, ensuring that critical applications receive the bandwidth they require, while less critical transmissions do not disrupt overall network performance. This is particularly crucial in environments where real-time communication is vital, such as in VoIP services.

Additionally, the platform incorporates state-of-the-art security features. With the increasing focus on cybersecurity in telecommunications, the MPE-33R includes encryption and authentication protocols to protect data and ensure secure communications. Operators can, therefore, provide peace of mind to their users, knowing that their information is safeguarded against potential threats.

In summary, Lucent Technologies MPE-33R is characterized by its versatility, modularity, advanced QoS capabilities, and robust security features. This multiprotocol platform effectively meets the demands of modern telecommunications, making it an invaluable asset for service providers looking to enhance their network offerings while adapting to the shifting technological landscape. As the need for integrated communication solutions continues to grow, the MPE-33R positions itself as a reliable and future-proof option for businesses worldwide.
Top Page Image Contents