Marquis Spas owner manual Installation Instructions, Location, Outdoor and Patio Installation

Page 10

INSTALLATION

INSTRUCTIONS

LOCATION

For your portable spa to function properly and safely, it must be located on a hard, flat, level surface. In-ground spas require special installation techniques and should be planned in conjunction with your spa dealer. Improper installation can result in structural damage to the spa and the voiding of your spa warranty. Items to discuss with your dealer include: Local construction codes, electrical service requirements, serviceability of equipment, present underground obstructions such as gas, water and telephone lines, safety measures such as fences, locks and visibility of the spa installation from the home, street and neighbors.

•You must allow for sufficient water drainage around the spa to help preserve the equipment and support structure.

•A filled spa can weigh a great deal and the location should support the weight of the filled spa.

•Locate the equipment compartment where it will be accessible. Your spa MUST be installed to permit access for servicing the equipment above and/or below any decks or floors. Access is essential and must allow adequate room for service.

•Leave access to the Circuit breakers in the subpanel (240V models) or to the interrupter switch (GFCI, 120V models) on the end of the power cord.

•Be sure the spa is level and in the final position BEFORE filling with water. Check for power cords, tools, and hoses that may be caught underneath the spa.

•IMPORTANT: DO NOT LET AN EMPTY SPA REMAIN EXPOSED TO

DIRECT SUNLIGHT FOR MORE THAN A FEW MINUTES. Spa surface tem- peratures can reach in excess of 150° F (65°C) if left exposed to the sun. Sig- nificant damage can occur if this is allowed to happen, including warping and blis- tering of the surface. Damage, which may occur as a result of this exposure, is not covered under the warranty.

•CAUTION: Never try to move a spa that has not been fully drained. To do so could result in damage to the spa and physical injury to the mover.

OUTDOOR AND PATIO INSTALLATION

To install the spa outdoors, we recommend a reinforced concrete pad at least four inches thick. The reinforcing material should be attached to a #10 AWG bonding wire per national and local electrical code.

If you place the spa on the ground, even temporarily, place concrete pavers under the entire bottom of the spa. The concrete pavers should be at least two inches thick and level across the entire surface. The spa will inevitably settle and become unlevel on this surface, thus it’s important to get it onto a solid foundation as soon as possible.

DECK INSTALLATION

Be sure the deck can support the weight of your filled spa by checking the deck’s maximum load capacity. Consult a qualified building contractor or structural engineer.

INDOOR INSTALLATION

There are special requirements if you place your spa indoors. Flooring material must provide a good grip when wet. Proper drainage is essential to prevent water puddling. Humidity will increase and it’s best to provide proper ventilation to the area and the addition of a ventilation system may be necessary.

page 9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YxtàâÜÇzAAA N U a L Welcome to the SPA LifeSerial Number Location Please Fill OUT and Keep for Future ReferenceIndex Safety Instructions VOLT, Cord and Plug Connected ModelsVOLT, Permanently Installed or Converted Models ALL SPA ModelsSafety Instructions for French Speaking SPA Owners Safety Sign Personal Safety General InformationPersonal Safety DO’S Personal Safety DO’S and DON’TSPersonal Safety DON’TS Deck Installation Installation InstructionsOutdoor and Patio Installation Indoor InstallationOverheating SHUT-OFF ValvesFreeze Protection Filter CartridgeVolt Electrical RequirementsTo Convert 120V to Start-up procedure for all models START-UP ProcedureStarting Your SPA Water Chemistry Guidelines Shock SanitationOperating Your SPA Pr Diagnostic MessageSafety Energy Cover Therapy PumpsMaximum Therapy Jetting System Power Boost JETPower Swirl JET JET Selector ValveCleaning the Exterior SPA MaintenanceDraining and Refilling the SPA Dura Base External Drain and Fill Valve Cleaning the SPA and Safety Energy CoverReinstalling the Filter Removing the FilterLight Bulb Replacement Winterizing Your SPASPA Maintenance Schedule SPA Care & Mainte Nance Schedule Troubleshooting Your SPA Recommended Chemical Levels SPA Water MaintenanceCause C and Solutions S to Water Maintenance Cloudy Water Chemical OdorEYE or Skin Irritation SPA Water Maintenance Scum Line in SPATOO Much Sanitizer in the Water Corrosion of MetalSPA Series Manuals R q u i s C o r p 6 H o f f m a n R o a d

Spas specifications

Marquis Spas has established itself as a leader in the spa and hot tub industry, known for its commitment to quality, innovation, and customer satisfaction. With a legacy that dates back to 1980, Marquis Spas offers a wide range of products designed to enhance relaxation, wellness, and social enjoyment.

One of the main features of Marquis Spas is their unique design that prioritizes user comfort and therapeutic benefits. The ergonomic seating in their spas provides optimal support for various body types, allowing users to unwind after a long day. The layout of the spas is carefully engineered to ensure that every seat provides a different experience, with tailored hydrotherapy options that target specific muscle groups.

Marquis Spas also incorporates advanced hydrotherapy technology into their products. The company’s exclusive "Intelligent Massage" system combines various jet types and configurations to deliver a customized massage experience. These hydrotherapy jets are strategically placed to relieve tension and promote circulation, which can contribute to overall wellness.

Energy efficiency is another hallmark of Marquis Spas. The brand employs state-of-the-art insulation techniques and energy-efficient components, ensuring that their spas maintain optimal water temperatures while minimizing energy costs. Features such as the "Eco-Mind" insulation system not only help to conserve energy but also enhance the lifespan of the spas.

In terms of convenience and accessibility, Marquis Spas includes cutting-edge control systems that allow users to operate their spas effortlessly. Features such as Bluetooth connectivity enable users to adjust settings, control lighting, and even play music directly from their smartphones. The intuitive control panels add a modern touch, ensuring that technology enhances the spa experience rather than detracts from it.

Durability and design aesthetics are also central to the Marquis Spas philosophy. The company uses high-quality materials that withstand the elements, ensuring that their spas retain their beauty and functionality over time. Customers can choose from a variety of finishes and colors, making it easy to find a spa that complements their outdoor space.

Overall, Marquis Spas combines innovative technology, thoughtful design, and a commitment to customer satisfaction to create an exceptional spa experience. Whether for relaxation, therapy, or socialization, Marquis Spas are thoughtfully designed to meet the diverse needs of users while enhancing their overall quality of life.
Top Page Image Contents