Regency U32-NG3 installation manual Hampton Cast Faceplate Installation

Page 16

INSTALLATION

HAMPTON CAST

FACEPLATE INSTALLATION

1)Lay the faceplate panels flat, face down on something soft so they don't scratch.

2)Attach the side filler brackets to the left and right sides using 3 screws and washer per side.

NOTE: There are filler brackets specifically for each side. The way to differentiate this is that on the side of the brackets there are 2 mounting holes. The side where there is a 7/16" gap from the top of the bracket to the mounting hole, must face the top.

3)Attach the right and left cast sides to the top using 2 screws per side.

5)Connect the ON/OFF switch wires by taking the black and red wires with the blue female ends thru the hole provided and connecting them to the ON/OFF switch.

6)Connect the fan switch wires by taking the black and red wires with the male ends (in the grey harness) thru the hole provided and connect them with the wire connec- tors from the fan speed con- trol.

7)Insert wires into the strain re- lief and install into switch box assembly.

8)Place the switch box assembly over the boss on the rear left side piece and secure with one screw.

Switch Box Assembly

Ensure that the top

and sides are

aligned.

Boss on rear left side

piece.

4)Use a measuring tape to ensure that the distance between the left and right side pieces is 28" (711mm).

28"

9)Tuck the wires into the faceplate to keep them away from the insert using the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side of the unit.

10)The power cord should be run behind the faceplate panel.

16

U32-3 FPI Direct Vent Gas Insert

Image 16
Contents U32 Gas Insert FPI GAS Insert To the NEW OwnerTable of Contents Safety Label Installation Materials Required Minimum Fireplace Dimensions Clearances to CombustiblesManufactured Mobile Home Additional Requirements GAS Connection Flue Liner InstallationVenting GAS Pipe Pressure Testing GAS Insert Aeration SystemOptional Brick Panel Natural Gas PropaneLOG SET Installation Rear View Trim Assembly Diagram Faceplate & Trim InstallationRear View Faceplate Assembly Diagram Optional Double Door Fire Screen Standard Flush DoorInstall bottom louver by sliding the two BAY LouversOptional BAY Door Optional BAY TrimBurner Orifice Diagram Remove the 2 screws holding the grate in positionFull Screen Front Hinge Hampton Cast Faceplate Installation Side Hook Slots Hampton Cast Faceplate Grill InstallationU32 Grill Stop Bracket Kensington Front Installation Screws ShownKensington Panel Door Installation Glass Door Sub-Frame HookOptional Wall Thermostat Optional Remote ControlFinal Check Wiring Diagram GreenOperating Instructions Maintenance Instructions Copy of Lighting Instruction PlateMaintenance General Vent MaintenanceDoor Glass Glass GasketGrate screws FAN MaintenanceReplacing fan Install a new gasket and reinstall the valve assembly Valve ReplacementShut off the gas supply Parts List Main AssemblyBurner Assembly & LOG SET Bay Door Flush DoorFaceplate Assembly Complete Custom Faceplate SetComplete Faceplate Set 402-933Hampton Cast Faceplate Assembly 187 189 188 194 203 201 207 195 205U32-3 FPI Direct Vent Gas Insert U32-3 FPI Direct Vent Gas Insert U32-3 FPI Direct Vent Gas Insert Warranty ConditionsInstaller Please complete the following information

U32-NG3 specifications

The Regency U32-NG3 is an innovative and elegant gas fireplace designed to enhance the ambiance of any living space while providing efficient heating. With its sleek design and modern technology, the U32-NG3 is a prime example of Regency's commitment to quality craftsmanship and customer satisfaction.

One of the main features of the U32-NG3 is its clean, contemporary lines that fit seamlessly into both traditional and modern interiors. The fireplace boasts a large viewing area, thanks to its expansive glass front. This design not only provides an unobstructed view of the flames but also allows for greater heat output, making the U32-NG3 an efficient choice for heating.

The U32-NG3 is designed with a direct vent system, which ensures that combustion gases are vented outside the home, promoting a clean indoor environment. This feature also maximizes the efficiency of the fireplace, as it draws air from outside for combustion, reducing heating costs. The direct vent technology is particularly beneficial for homes in colder climates as it minimizes the draw of warm air from the living space.

In terms of heating capacity, the U32-NG3 is powerful, capable of delivering up to 30,000 BTUs. This output is suitable for medium to large rooms, ensuring a cozy atmosphere on cold winter evenings. Homeowners can also customize the flame height and heat output to suit their comfort needs.

Safety is a top priority with the U32-NG3. It includes advanced safety features such as an automatic shut-off system that activates in case of a malfunction or blockage in the venting system. The fireplace also has a safety screen that prevents unintended contact with the flames while allowing for maximum heat circulation.

The U32-NG3 is equipped with state-of-the-art electronic ignition, which ensures quick and reliable startups at the push of a button. Additionally, the fireplace can be operated remotely with a convenient wall switch or optional remote control, adding further ease of use.

In conclusion, the Regency U32-NG3 is a versatile gas fireplace that combines style, efficiency, and advanced technology. Its focus on safety, ease of use, and impressive heating capabilities make it an ideal choice for homeowners looking to upgrade their living space with a modern heating solution. With the U32-NG3, you can create a warm and inviting atmosphere while enjoying all the benefits of a high-quality gas fireplace.