Regency U32-NG3 Materials Required, Minimum Fireplace Dimensions Clearances to Combustibles

Page 6

INSTALLATION

1)

Check all clearances to combustibles, page

 

6.

2)

Make the gas connection. See page 7.

3)

Install the 3" flue liner to the sliding connec-

 

tor plate. See page 7.

4)

Slide the unit half way into the fireplace.

5)

Pull the vent connector plate through the

 

tapered brackets and fasten to the front

 

plate. See page 7.

6)

Slide the unit fully into the fireplace.

7)

Test gas pressure, page 8. Check aeration

 

system, page 8.

8)

Install the optional brick panels. See page 8.

9)

Install the log set. See page 9.

10) Assemble and install the faceplate and trim.

 

See page 10.

MATERIALS REQUIRED

No electrical power supply is required for the gas control to operate. A 120 Volt AC power cord is hooked up to the fan. Plug the 3 wire cord into a suitable receptacle. Do not cut the ground terminal off under any circum- stances. When connected with 120 volts, the appliance must be electrically grounded in ac- cordance with local codes, current version of CSA C22.1 (in Canada) or in the absence of local codes, with the National Electrical Code ANSI/NFPA 70-1987.

NOTE: This unit is equipped with a heat sensor thermodisc which will prevent the blower from operat- ing until the unit reaches the cor- rect temperature.

MINIMUM FIREPLACE

DIMENSIONS

CLEARANCES TO COMBUSTIBLES

Minimum Clearances to Combustibles

From Unit

 

Sides

A

10" / 255 mm

Ceiling

B

47.5" / 1205 mm

Mantel

C

see Dia. 2 & 3

From Standard Surround (26" x 40")

Sides

D

4" / 100 mm

Ceiling

E

41.5" / 1055 mm

Mantel

 

see Dia. 2 & 3

Max. Mantle Depth

G

12" / 305 mm

 

 

(see Dia. 2)

Hearth Height

H

0" / 0 mm

Hearth Depth

I

16" / 405 mm

Hearth Width

J

40" / 1015 mm

Min. Alcove Width

K

48" / 1220 mm

Max. Alcove Depth

L

36" / 915 mm

11) Install the glass front (flush or bay). See

pages 10 and 11.

12) Install optional glass trim, or door fire

screens. See pages 11 and 12.

13) Install both louvers (flush or bay). See

pages 11 and 12.

14) Install optional remote control or wall ther-

mostat, pages 20.

15) Final check: Before leaving this unit with

the customer, the installer must ensure that

the appliance is firing correctly. This in-

cludes:

a)

Clocking the appliance to ensure the

 

correct firing rate.

b)

Adjusting the primary air, if required, to

 

ensure that the flame does not carbon.

 

See page 8.

c)

Ensuring that the appliance is venting

 

correctly.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1)Ensure that structural members are not cut or weakened during installation.

2)Ensure proper grounding using the #8 ground lug provided.

3)Appliance must be anchored to the floor with the supplied anchoring methods.

The minimum fireplace clearances & dimen- sions for the FPI gas insert are shown in the following diagrams:

Diagram 1

Combustible Mantel Clearances

with Bay & Flush Louvers in

Masonry and Factory Built

Fireplace Installation

*Note: If you are installing the Molded Faceplate, the minimum fireplace dimen- sions are as follows:

Width (at front): 29"

(737mm)

Depth:

15"

(381mm)

Diagram 2

6

U32-3 FPI Direct Vent Gas Insert

Image 6
Contents U32 Gas Insert FPI GAS Insert To the NEW OwnerTable of Contents Safety Label Installation Minimum Fireplace Dimensions Clearances to Combustibles Materials RequiredManufactured Mobile Home Additional Requirements Flue Liner Installation GAS ConnectionVenting Optional Brick Panel GAS Pipe Pressure TestingGAS Insert Aeration System Natural Gas PropaneLOG SET Installation Faceplate & Trim Installation Rear View Trim Assembly DiagramRear View Faceplate Assembly Diagram Optional Double Door Fire Screen Standard Flush DoorOptional BAY Door Install bottom louver by sliding the twoBAY Louvers Optional BAY TrimBurner Orifice Diagram Remove the 2 screws holding the grate in positionFull Screen Front Hinge Hampton Cast Faceplate Installation Hampton Cast Faceplate Grill Installation Side Hook SlotsU32 Grill Stop Bracket Kensington Front Installation Screws ShownKensington Panel Door Installation Glass Door Sub-Frame HookOptional Remote Control Optional Wall ThermostatFinal Check Wiring Diagram GreenOperating Instructions Maintenance Instructions Copy of Lighting Instruction PlateDoor Glass MaintenanceGeneral Vent Maintenance Glass GasketFAN Maintenance Grate screwsReplacing fan Valve Replacement Install a new gasket and reinstall the valve assemblyShut off the gas supply Parts List Main AssemblyBurner Assembly & LOG SET Bay Door Flush DoorComplete Faceplate Set Faceplate AssemblyComplete Custom Faceplate Set 402-933Hampton Cast Faceplate Assembly 187 189 188 194 203 201 207 195 205U32-3 FPI Direct Vent Gas Insert U32-3 FPI Direct Vent Gas Insert U32-3 FPI Direct Vent Gas Insert Warranty ConditionsInstaller Please complete the following information

U32-NG3 specifications

The Regency U32-NG3 is an innovative and elegant gas fireplace designed to enhance the ambiance of any living space while providing efficient heating. With its sleek design and modern technology, the U32-NG3 is a prime example of Regency's commitment to quality craftsmanship and customer satisfaction.

One of the main features of the U32-NG3 is its clean, contemporary lines that fit seamlessly into both traditional and modern interiors. The fireplace boasts a large viewing area, thanks to its expansive glass front. This design not only provides an unobstructed view of the flames but also allows for greater heat output, making the U32-NG3 an efficient choice for heating.

The U32-NG3 is designed with a direct vent system, which ensures that combustion gases are vented outside the home, promoting a clean indoor environment. This feature also maximizes the efficiency of the fireplace, as it draws air from outside for combustion, reducing heating costs. The direct vent technology is particularly beneficial for homes in colder climates as it minimizes the draw of warm air from the living space.

In terms of heating capacity, the U32-NG3 is powerful, capable of delivering up to 30,000 BTUs. This output is suitable for medium to large rooms, ensuring a cozy atmosphere on cold winter evenings. Homeowners can also customize the flame height and heat output to suit their comfort needs.

Safety is a top priority with the U32-NG3. It includes advanced safety features such as an automatic shut-off system that activates in case of a malfunction or blockage in the venting system. The fireplace also has a safety screen that prevents unintended contact with the flames while allowing for maximum heat circulation.

The U32-NG3 is equipped with state-of-the-art electronic ignition, which ensures quick and reliable startups at the push of a button. Additionally, the fireplace can be operated remotely with a convenient wall switch or optional remote control, adding further ease of use.

In conclusion, the Regency U32-NG3 is a versatile gas fireplace that combines style, efficiency, and advanced technology. Its focus on safety, ease of use, and impressive heating capabilities make it an ideal choice for homeowners looking to upgrade their living space with a modern heating solution. With the U32-NG3, you can create a warm and inviting atmosphere while enjoying all the benefits of a high-quality gas fireplace.