Lopi Revere Planning The Installation, Preparation for Installation, Installation Considerations

Page 7

Stove Installation (for qualified installers only)

7

SAFETY NOTICE:

Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area.

Planning The Installation

We suggest that you have an authorized Travis Industries dealer install your fireplace insert. If you install the fireplace insert yourself, your authorized dealer should review your installation plans.

Check with local building officials for any permits required for installation of this fireplace insert and notify your insurance company before proceeding with installation.

Preparation for Installation

Check for damage to the exterior of the fireplace insert (dents should be reported, scratches can be fixed by applying touch up paint).

Check the interior of the firebox (replace cracked firebrick and make sure baffle is in place).

The fireplace insert can be lightened by removing the firebricks and baffle (pg 25) - replace before operation.

Additional Accessories Needed for Installation

1Door Shell (Black 99300195 Brass 99300196 or Pewter 99300197 - see pg 29)

2 Surround Panels (see page 31)

Installation Considerations

Installation Type

Considerations

 

 

Insert with Positive Flue (Full Reline)

• Utilizes existing masonry or zero clearance fireplace

(Page 12)

• Provides best draft

• Easiest to clean

 

Insert with Direct Connect Flue

• Utilizes existing masonry or zero clearance fireplace

(Page 12 and 13)

• Provides good draft

• Requires fireplace block-off plate - see page 11

 

Insert with Face Seal Connection

• Utilizes existing masonry fireplaces with cross section

(Page 13)

of 28" to 144" (not approved for zero clearance

fireplaces)

NOTE: Before installing verify with local building

• Provides okay draft

officials that this type of installation is

• Easiest to install

approved in your area.

• Requires the optional surround panels and insulation

 

(see "Surround Panels" on page 31).

© Travis Industries

100-01165

4040806

Image 7
Contents Revere Fireplace Insert 2Introduction Mail your Warranty Card Today, and Save Your Bill of SaleIntroduction Important Information Table of Contents Ashes Safety PrecautionsMobile Travis Industries, Inc. grants no warranty, implied orDimensions Features & SpecificationsInstallation Options Features Heating SpecificationsInstallation Considerations Planning The InstallationPreparation for Installation Additional Accessories Needed for InstallationFireplace Requirements Minimum Fireplace SizeHearth Requirements Insert Placement RequirementsMasonry Fireplace Requirements Zero-Clearance Metal Fireplace Requirements Leveling Bolt InstallationDrafting Performance Block-Off Plate Template Block-Off Plate InstallationFireplace Insert with Positive ConnectionInsert with Direct MasonryInsert with Face Seal Connection Insert with Direct Connection Z.C. FireplaceOpening the Door Safety NoticeOperating Your Appliance Before Your First FireBypass Operation Starting a Fire Approximate Air Control Settings Adjusting the Burn RateAsh Removal Normal Operating Sounds Optional Blower OperationRe-Loading the Stove Overnight BurnSelecting Wood Testing Wood MoistureWhy Dry Wood is Key Hints for BurningTroubleshooting Remove Ash if necessary Daily Maintenance while stove is in useClean the Glass if necessary Maintaining Your ApplianceDoor and Glass Inspection Monthly Maintenance while appliance is in useCreosote Formation and Need for Removal Firebrick and Baffle Inspection Yearly MaintenanceCleaning the Air Duct and Blower if applicable Touch Up PaintReplacing the Door Handle Door PartsReplacing the Glass Replacing the Door GasketFirebox Parts Floor and Side Firebrick Removal & ReplacementAir Tube Removal & Replacement Baffle Removal & ReplacementYears 6 & 7 Coverage Parts only Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 3 Through 5 Coverage Parts & LaborListing Label Listing LabelOptional Equipment Door Shell InstallationHex Wrench Arched Panels Installation InstructionsSurround Panels Rectangular PanelsTop Trim Panel Bracket Right Side Front Blower To Switch The Power Cord To The Left SideIndex

Revere specifications

The Lopi Revere is a highly efficient and stylish wood stove that stands out in the market for its superb heating capabilities and modern design. Ideal for both residential and commercial settings, the Revere model seamlessly combines traditional wood-burning aesthetics with cutting-edge technology to deliver an optimal heating experience.

One of the main features of the Lopi Revere is its impressive heat output. The stove produces up to 75,000 BTUs, making it suitable for heating spaces ranging from 1,000 to 2,500 square feet. This makes the Revere an excellent choice for those living in larger homes or those seeking to create a cozy atmosphere in expansive living areas. The extended burn time of up to 12 hours on a single load of wood ensures that users can enjoy prolonged warmth without the hassle of constant reloading.

The Lopi Revere is constructed from high-quality materials, ensuring durability and longevity. The heavy-duty steel body not only adds to the aesthetic appeal but also enhances heat retention and distribution. Additionally, its ceramic glass door allows users to enjoy a captivating view of the flames while maintaining safety and efficiency. The large firebox can accommodate logs up to 20 inches, providing ample room for longer burn times.

Equipped with advanced combustion technology, the Lopi Revere ensures a clean and efficient burn. The stove features a secondary combustion system that maximizes heat output while minimizing emissions. By utilizing a combination of primary and secondary air controls, the Revere achieves optimal airflow, resulting in a cleaner burn that is more environmentally friendly.

Another characteristic that sets the Lopi Revere apart is its ease of use. The simple, adjustable air intake and ash removal system allow for seamless operation and maintenance. Users can easily regulate the heat output and control the burn rate according to their specific heating needs.

With its versatile design, the Lopi Revere is available in several finishes, including classic black and modern painted options, allowing homeowners to match the stove to their interior style. Whether positioned in a rustic cabin or a contemporary home, the Lopi Revere adds both functionality and aesthetic value.

In summary, the Lopi Revere is a modern wood stove that brings together efficiency, style, and advanced technology, making it an outstanding choice for anyone looking to enhance their home heating experience.