Lopi Direct Vent Freestanding Stove owner manual Correct

Page 18

1 8 Finalizing the Installation (for qualified installers only)

6Let the heater burn for thirty minutes. Adjust the air shutter, if necessary, to achieve the correct looking flame (see the illustration below).

•The air shutter adjusts the amount of air that mixes with the gas before it exits the burner holes. It is used to fine-tune the flame for differences in altitude and vent configuration.

ADJUSTING THE AIR SHUTTER

Pushing to the left gives the flame less air (making it more orange). Pushing to the right gives the flame more air, making it more blue. For fine adjustments use a screwdriver to tap the air shutter.

NOTE: If the air shutter is all the way open, yet the flames remain sooty, shut off gas to the fireplace and contact a qualified gas service technician.

Gas Control Valve

Air Shutter Control

NOTE: The logs must be installed correctly to monitor the flame while adjusting the air shutter.

Correct

Flames should be blue at the base, yellow-orange on the top.

Not Enough Air

Too Much Air

If the flames are too tall or sooty on the

If the flames are all blue and

ends, open the air shutter.

short, close the air shutter.

!If the vent configuration is installed incorrectly the vent may cause the flames inside the heater to lift or “ghost” – a dangerous situation. Inspect the flames after installation to insure proper performance. If the vent configuration is correct, yet the flames are lifting or ghosting, shut off gas to the heater and contact the dealer for information on remedying the problem.

!Failure to properly adjust the air shutter may lead to improper combustion and a safety hazard. Consult your dealer or installer if you suspect an improperly

 

Burner Ports

Burner Pan

(holes)

The flames should burn right off the top of the burner ports (if they are too blue, adjust the air control).

If the flames are lifting, yet the vent configuration is correct, contact your dealer.

If the flames are ghosting, yet the vent configuration is correct, contact your dealer.

7Turn the flame adjust knob to its highest position - the flames should be tall enough, but not touching the top of the firebox. Check the flame on low position. The flames should burn off of each burner hole. If the heater does not work correctly, contact your dealer for a remedy.

8Give this manual to the home owner and fully explain the operation of this heater.

Travis Industries

1 0 0 - 0 1 1 4 2

4 0 5 0 1 1 4

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Featuring the Burner 2Introduction Introduction Important InformationTravis Industries 0 0 1 1 4 5 0 1 1 Table of Contents Safety Precautions If YOU Smell GASThis Manual Dimensions & Weight 6SpecificationsHeating Specifications Electrical Specifications for optional blowerInstallation Warnings Installation OverviewPacking List Additional Items Required Installation Hints Stove ClearancesMobile Home Requirements Heater Placement Requirements Floor Protection RequirementsGas Line Installation Gas Inlet PressureVent Requirements Manuafacturer R i e sApproved Vent Configurations Restrictor PositionDiffuser Plate Removal Measuring Vent Lengths Approved Venting Configurations for Horizontal Terminations Approved Venting Configurations with a Vertical Termination Propane LPVent Termination Requirements see illustration below Finalizing the Installation Correct Glass Removal Re-Attaching the Glass FrameGlass Frame Removal and Installation Log Installation Installing the Rock Wool2Operation Before You Begin Location of Controls See explanation belowOperation Starting The Pilot FlameStarting the Stove for the First Time Adjusting the Flame Height4Operation Turning the Stove On and OffNormal Operating Sounds Adjusting the Blower Speed optionalOperation2 Normal Operating OdorsPainted Surfaces Yearly Service ProcedureMaintaining Your Stoves Appearance GlassMaintenance TroubleshootingHow this Stove Works What Turns the Main Burners On and OffWhat Prevents Gas Buildup Wiring Diagram Replacement Parts ListSafety Label SturbridgeYears 3 Through 5 Coverage Parts & Labor Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyOptional Accessories Burner Replacement LP Conversion InstructionsApply thread sealant to the new orifice and install Install the log set see Replace the glass see Blower Attach the blower following the directions belowDo not plug Heater Until Installation is Complete Fireback Stone or Cast Inserts 0Installation Addenda Addendum #1 Class a Chimney Conversion KitInstallation Addenda Addendum #2 Masonry ChimneyConversions 2Index

Direct Vent Freestanding Stove specifications

The Lopi Direct Vent Freestanding Stove stands out as a leading choice for homeowners seeking efficient and elegant heating solutions. Known for its innovative design and advanced technology, the stove combines aesthetic appeal with exceptional performance, making it an ideal addition to any living space.

One of the main features of the Lopi Direct Vent Freestanding Stove is its direct venting system. This technology allows the stove to draw air from outside for combustion and eject exhaust gases outdoors, ensuring optimal indoor air quality. This not only enhances efficiency but also eliminates the need for a traditional chimney, making installation simpler and versatile.

The stove's design is both modern and traditional, featuring clean lines and a variety of finishes to complement any décor. Available in different sizes, the Lopi stove can fit comfortably in various spaces while providing powerful heating. Its large viewing window invites warmth and ambiance, allowing users to enjoy the mesmerizing flames without compromising heat output.

Boasting impressive heating capabilities, the Lopi Direct Vent Freestanding Stove has a high BTU output, effectively warming spaces even in the coldest of climates. The unit is equipped with a robust heat exchanger that maximizes heat retention while minimizing fuel consumption. Furthermore, the stove can operate using either natural gas or propane, offering flexibility based on availability and preference.

In terms of efficiency, many models in this line come with an EPA certification, demonstrating a commitment to environmentally friendly practices. With features such as adjustable flame settings and a thermostatic remote control, users can easily customize their heating experience, ensuring comfort at all times.

Safety is also a priority with the Lopi Direct Vent Freestanding Stove. It includes built-in safety features such as a protective screen and cool-to-the-touch body, making it suitable for homes with children or pets. The durable construction ensures longevity, with high-quality materials designed to withstand the test of time.

In summary, the Lopi Direct Vent Freestanding Stove combines sleek aesthetics with cutting-edge technology to deliver an unparalleled heating solution. With its array of features, efficiency, and safety measures, it not only enhances home comfort but also adds a touch of elegance to any living environment. Whether enjoying the warmth on a chilly evening or creating a cozy atmosphere, the Lopi stove stands out as a top choice for modern homeowners.
Top Page Image Contents