Precisionaire ST55R-2020, SAR1P20-2424 specifications Media Rolls, Media Pads, SAR-1, 1GT, FP3

Page 3

Manufacturing

Specifications

For for Media Rolls & Blankets

Standard specifications:

MEDIA ROLLS

1.Roll lengths are +/- 5% and widths are -0/+1/2".

2.Maximum roll widths are:

SA600-G1090.55"

SAR-190.55"

All other polyester medias 110"

Fiberglass media

84"

3. Roll Lengths are:

 

SA600-G10

792"

SAR-1

100 ft.

FP3

50 ft.

1GT

90 ft.

PS125

90 ft.

All other polyester media

100ft.

Fiberglass media

300 ft.

4.Any width can be custom cut from 6" to maximum width for any media product.

5.Rolls are bagged in minimum 3-mil clear plastic bags.

6.Rolls are identified with a tag on top of each bag.

7.Rolls are individually packaged on LTL orders.

8.All rolls are knife cut without the use of hot wires.

MEDIA PADS

1.Pad dimensions are -1/4"/+1/2" in each direction.

2.SA600-G10 and SAR-1 pads are bagged and boxed. Full perimeter of box is also taped.

3.All other pads are boxed only.

4.Fiberglass pads are available in vacuum-packed form.

25pads per bag and 4 bags in each box for 100 filters per case.

5.SA600-G10 pads are folded exit side to exit side and rolled to prevent contamination from collecting on the exit side of the media.

6.All rolls are knife cut without the use of hot wires.

MEDIA

Each media has its own specifications for weight per square foot, loft, chemical resin weights, tackfier weights, MSDS sheets, etc. These documents may be obtained by contacting our corporate office.

Media Varieties:

SA600-G10

Each SA600 media pad and roll has its own model numer. No custom sizes are used for this media type.

Model Number

EX. SA600-361 or SA600-1001

The first 5 digits identify the SA600-G10 media. If there are three digits after the hyphen then it is a pad. If there are four digits after the hyphen, then it is a roll. Model Number descriptions must be looked up to identify the cor- rect size, and each model number has a specific case quantity.

SAR-1

Each SAR-1 media roll and pad also have their own model number.No custom sizes are used for this media type.

Model Number

EX. SAR1M-24120 or SAR1R-55

The first 4 digits identify the SAR-1 media. If the fifth digit is an M, then its a media pad, if its an R, then its a media roll. For the pads, the first two digits after the hyphen iden- tify the pad width in inches, and the remaining digits iden- tify the pad length in inches. For the rolls, the remaining digits identify the roll width in inches.

1GT

1GT media is available in rolls, pads and custom pads. All model numbers start with 1GT. The fourth digit is R for roll, P for pad, and C for custom. After the hyphen, the digits for rolls equal the roll length, the pad size is only listed in the description, and the digits following the hyphen for custom pads signify the total square inches for the custom pad.

330G,331Y,332

Fiberglass media are available in rolls, pads, custom pads, and vacuum packed pads. For the 330G and 331Y, the first two digits after the hyphen identify the roll length and if the last digit is a 0,1,or 2 then the length equals 200 ft. and if it equals 3 then its 300 ft. The 332 uses a "-300" for all 330 ft. rolls. The pads sizes are listed after the hyphen and if there is a 0 as the first digit after the hyphen then the last two digits are the pad width. If there is a V as the fourth digit, then the pads are vacuum packed.

FP3

If there are only two digits after the hyphen, then its a roll and the width equals the two digits. If there are four digits after the hyphen, then its a pad and the dimensions are listed. Custom pad square inches are also listed after the

169

Image 3
Contents Standard Size Single Panels DimensionsWire Rings Media SpecificationCube Varieties Filter DimensionsWire Supports Media1GT Media RollsMedia Pads SAR-1HOW to Find Custom PAD Pricing