Pella V981553 Interior Seal, Sealing the Door to the Exterior Wall Cladding

Page 6

I.Install screen by inserting the top of the screen into the screen pocket located at the exterior head of the patio door. Compress the top rollers just enough to allow the bottom of the screen to be inserted onto the bottom screen track. Adjust the screen rollers by turning the adjustment screw located at the top and bottom until the screen operates smoothly and is plumb and centered from top to bottom. Install the screen keeper if desired.

6 INTERIOR SEAL

Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer's recommendations for application. Use of high pressure foams or improper application of the foam may cause the door frame to bow and hinder operation.

A.Apply insulating foam sealant. From the interior, insert

the nozzle of the applicator approximately 1" deep into the space between the door and the rough opening and apply a 1" deep bead of foam. This will allow room for expansion of the foam and will minimize squeeze out. If using foam other than Great Stuff ™ Window and Door Insulating Foam Sealant by the Dow Chemical Company, allow the foam to cure completely (usually 8 to 24 hours) before proceeding to the next step.

Note: It may be necessary to squeeze the end of the tube

 

with pliers to be able to insert into the space between the

 

door frame and the rough opening. DO NOT completely

 

fill the space from the back of the fin to the interior face

È

of the door.

 

B.On the interior, seal the door sill to the floor with a corner bead of sealant. Connect this bead of sealant to the insulating foam at both door jambs.

C.Check door operation by opening and closing the door.

Note: If the door does not operate correctly, check to make sure it is still plumb, level, square and that the sides are not bowed. If adjustments are required, remove the foam with a serrated knife. Adjust the shims, and reapply the insulating foam sealant.

7 SEALING THE DOOR TO THE EXTERIOR WALL CLADDING

Note: When applying siding, brick veneer or other exterior finish materials, leave adequate space between the door frame and the material for sealant. Refer to the illustration that corresponds to your finish material. Not allowing adequate space or not using backer rod may cause the sealant to break down prematurely and allow water to infiltrate.

BRICK VENEER

Insulating

Foam

1/2"

1/2" Min.

 

VINYL/STEEL

WOOD SIDING

 

SIDING

 

WITH TRIM

 

 

Backer rod

Backer rod

 

and

and

Backer rod

sealant

sealant

and

typical

typical

sealant

Insulating

Insulating

typical

Foam

Foam

 

 

1/2"

1/2"

 

 

 

 

 

 

1/2" Min.

1/2" Min.

 

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Vinyl Windows and Doors Fold the water resistive barrier 1D. Fold side flaps into Rough Opening PreparationCut the water resistive barrier 1C Tab the sill flashing tape and fold. Cut 1 wide tabs at eachPrepare the Door for Installation Setting and Fastening the DoorIntegrating the Door to the Water Resistive Barrier Fasten the door to openingReinstall the Sliding Panel Interior Seal Sealing the Door to the Exterior Wall CladdingApply insulating foam sealant. From the interior, insert Installation Instructions Bottom FIN Removal Insert closed cell foam backer rod into the space aroundRemove the sill and screen tracks from the door Rotate the handle 180 and install the door handle byInstructions Reversing Door Slide Remove the door handle by removing the twoCleaning Instructions Important Notice

V981553 specifications

The Pella V981553 is a premium window offering that combines innovative design with advanced technologies to enhance both aesthetic appeal and energy efficiency. This window model is part of Pella's renowned product line, known for its durability, style, and environmental performance.

One of the standout features of the Pella V981553 is its exclusive InsulShield technology. This advanced glass option significantly reduces heat transfer, ensuring that homes remain comfortable regardless of the weather outside. The technology utilizes multiple panes of glass, along with gas fills like argon or krypton, to create an effective thermal barrier. This not only enhances comfort but also helps homeowners save on energy bills.

In terms of design, the Pella V981553 is highly customizable. Homeowners can choose from a variety of styles, colors, and finishes to complement their home’s architecture. The window is available in different grid patterns and configurations, allowing for personalized aesthetics that suit any design preference. Additionally, Pella provides options for decorative glass, which can add a unique touch while maintaining privacy.

Durability is another hallmark of the V981553 model. It features constructed frames made from high-quality materials that resist warping, fading, and cracking. The window’s exterior is often coated with a protective finish that enhances longevity and reduces maintenance needs, allowing homeowners to enjoy their investment without the hassle of frequent upkeep.

The Pella V981553 also prioritizes security, employing robust locking mechanisms that provide peace of mind. The use of laminated glass further enhances safety by reducing the likelihood of breakage.

Installation of the Pella V981553 is designed to be user-friendly. Pella’s windows come with pre-drilled frames, which simplifies the process for builders and homeowners alike. The product is engineered to fit standard openings, minimizing the need for extensive modifications during installation.

Overall, the Pella V981553 exemplifies a commitment to quality, innovation, and style. With its energy-efficient features, customizable options, and robust construction, it is a smart choice for homeowners looking to enhance their living spaces while adhering to modern standards of performance and aesthetics. Whether for new builds or renovations, the Pella V981553 is a testament to Pella’s dedication to superior craftsmanship.
Top Page Image Contents