Setting and Fastening the Door | Pella 808SQ102 guide

3SETTING AND FASTENING THE DOOR (continued)

*OUFSJPS	Î
'JYFE1BOFM	5ISFTIPME

&YUFSJPS

"SDIJUFDU4FSJFTBOE%FTJHOFS4FSJFT

G. Architect Series and Designer Series: Apply sealant and insert a #8 x 2-1/2" screw (provided) into each hole in the bottom of the door frame (shown above in gold).

H. Architect Series and Designer Series: Position and secure the panel retainer by drilling pilot holes through the remaining holes in the retainer into the sill support or wood blocking, then apply sealant to the holes and insert a screw into each hole as speciﬁed below.

Aluminum sill support: 9/64" pilot holes, #10 x 3/4" thread cutting screws (provided).

Wood blocking: 1/8" pilot holes, #10 x 2-1/2" ﬂat head wood screws (provided).

Masonry ﬂoor: 3/16" x 1-3/4" concrete screw. Pilot drill per screw manufacturer’s recommendations.

I.Remove the factory installed screws from the retainer and repeat the process.

J.Architect Series and Designer Series: Drill a 3/16" clearance hole at each indentation in the extrusion at the top of the door frame into the rough opening, stopping when the drill is through the door frame. Apply sealant to each hole, then insert a #8 x 3" stainless steel screw into each hole.

4 INTEGRATING THE DOOR TO THE BUILDING FELT

Note: The ﬂashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. Pre-folding the tape 1/2" before removing the paper backing will make it easier to apply the tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant line will cover the exterior edge of the tape.

A. Apply side ﬂashing tape. Cut 2 pieces of ﬂashing tape 4" longer than the frame height of the door. Apply one piece 1/2" up onto the frame cladding, over the nailing ﬁn and onto the ﬂashing paper to each side. The tape should extend 2" above the top of the door and 2” below the bottom of the door. Press the tape down ﬁrmly while folding down the excess tape at the top and bottom of the door.

B.Apply top ﬂashing tape. Cut a piece of ﬂashing tape long enough to go across the top of the door and extend at least 1" past the side ﬂashing tape on both sides. Apply the tape 1/2" up onto the frame cladding, over the top nailing ﬁn as shown. Fold the overlapping tape down, and press all tape down ﬁrmly.

Note: The top ﬂashing tape must overlap the side ﬂashing tape to prevent water from getting behind it.

{

C. Apply the top ﬂashing paper. Cut one piece of ﬂashing paper at least 21" longer than the width of the rough opening. Position the bottom edge of the ﬂashing paper ﬂush with

the frame of the door and center the ﬂashing paper with the width of the door. Staple the{ ﬂashing paper to the header.

Note: When applying the ﬁrst layer of building felt, ensure the sill ﬂashing paper overlaps the building felt. This will tie the door system into the building water management system.

808SQ102 specifications

The Pella 808SQ102 is a remarkable window offered by Pella Corporation, renowned for its high-quality window and door solutions. This specific model combines aesthetic appeal with innovative technology, making it a top choice for homeowners looking to enhance their living spaces.

One of the standout features of the Pella 808SQ102 is its energy efficiency. Equipped with advanced insulating technologies, this window is designed to minimize heat transfer, helping to regulate indoor temperatures. The dual-pane glass, featuring Low-E (low emissivity) coatings, enhances thermal performance by reflecting heat back into the room during winter while keeping unwanted heat out during summer. This not only creates a more comfortable living environment but can also lead to significant energy savings.

In terms of durability, the Pella 808SQ102 is built to last. Its strong, composite frame resists warping, cracking, and fading, ensuring that the window maintains its appearance and functionality over time. Additionally, the window is designed to withstand harsh weather conditions, making it suitable for a variety of climates. The low-maintenance exterior is another attractive characteristic; it only requires occasional cleaning to look new, freeing homeowners from the hassle of frequent upkeep.

The Pella 808SQ102 also boasts a variety of aesthetic options. It is available in multiple colors and finishes, allowing homeowners to choose a look that complements their home’s architectural style. Furthermore, the window includes customizable grid patterns, which can add a touch of elegance and character to any space. The sleek, contemporary design enhances natural light entry, creating an inviting atmosphere indoors.

Security features are also paramount in the Pella 808SQ102 design. The window is equipped with advanced locking systems to provide peace of mind, ensuring that homes remain secure against intrusions. Additionally, the window meets or exceeds industry performance standards, making it a dependable choice for residential properties.

In summary, the Pella 808SQ102 is a blend of innovation, aesthetics, and durability. Its energy-efficient design, durability against the elements, low maintenance requirements, customizable aesthetics, and enhanced security features make it an excellent choice for those seeking quality windows for their homes. Pella’s commitment to superior craftsmanship is evident in this model, providing homeowners with a reliable solution for their window needs.