III. Getting Started, Oil Burner | Northern Industrial Tools 157494

III.) Getting Started

IMPORTANT: Proper initial installation of equipment will assure more satisfactory performance, longer service life, and lower maintenance cost.

Make sure the water heater is on a level surface and in a protected area where it is not readily influenced by outside forces such as freezing temperatures, strong winds, rain, etc. Locate the water heater for easy access to fill fluids and make adjustments. It is recommended that a partition is made between the wash area and the water heater to prevent direct nozzle spray from coming in contact with the water heater. Excessive moisture will reduce the water heater’s service life.

Partition

IV.) Venting

DANGER: Do not run machine indoors or in an enclosed area without adequate ventilation, or in areas where flammable vapors, (gasoline, solvents, etc.) may be present. Do not vent exhaust gases into a wall, a ceiling, or a concealed space.

CAUTION: All venting must be in accordance with applicable federal and state laws, and local ordinances. Consult local heating contractors.

If the water heater is to be used in an enclosed area, a flue must be installed to vent burner exhaust to the outside atmosphere. Be sure the flue is the same size as the burner exhaust vent on the water heater lid. Poor draft will cause the water heater to soot and not operate properly. When selecting the location for installation, beware of poorly ventilated locations or areas where exhaust fans may cause an insufficient supply of oxygen. Proper combustion can only be obtained when there is a sufficient supply of oxygen available for the amount of fuel being burned. If it is necessary to install a unit in a poorly ventilated area, outside fresh air may have to be piped to the burner and a fan installed to bring sufficient air into the unit. Locate the water heater in such a manner that the flue will be as straight as possible and protrude through the roof at a proper height and location to provide adequate draft. This oil fired unit must have a draft controller installed in the flue (Part #18007 call 1-800-270-0810 to order). A draft controller will permit proper upward airflow of exhaust flue gases.

V.) Oil Burner

Burner Air Adjustment: The oil burner is preset and performance tested at the factory (elevation 1100 feet).

Aone-time initial correction of the burner for your location will pay off in economy, performance, and extended service life.

Air Band

White

Arrow

	Locking	Burner
	Screw	Burner
	Screw

1.) Turn the pump and heat switches on (Refer to “Operation” for details). Have someone operate the spray gun so the burner fires.

2.) Loosen the locking screw and close the air band until black smoke appears from the burner exhaust vent. Note the position of the white arrow on the air band.

3.) Slowly open the air band until white smoke just starts to appear.

4.) Turn the air band half way back to the black smoke position previously noted. Tighten the locking screw.

5.) Fine tune the burner air by loosening the shutter lock screw and turning the shutter until the exhaust is cleanest. Tighten the shutter lock screw.

Shutter

Lock Screw

CAUTION: If white smoke appears from the burner exhaust vent during start-up or operation, discontinue use and readjust air bands.

NOTE: If a flue is installed, have a professional serviceman adjust your burner for a #1 or #2 smoke spot on the Bacharach scale.

157494 specifications

Northern Industrial Tools 157494 is a high-performance air compressor designed to meet the demands of both professional and DIY applications. Known for its durability and efficiency, this compressor stands out in the crowded market of industrial tools. One of the primary features of the Northern Industrial Tools 157494 is its robust construction, which includes a heavy-duty pump that ensures long life and reliable performance. The compressor is equipped with a powerful motor that delivers a substantial amount of air pressure, allowing it to tackle a variety of tasks, from inflating tires to powering pneumatic tools.

One of the key technologies utilized in the Northern Industrial Tools 157494 is its oil-lubricated pump system. This technology enhances the lifespan of the compressor by minimizing wear and tear, ultimately providing a quieter and more efficient operation. The oil-filled pump also ensures optimal cooling and lubrication, which are crucial for maintaining performance during extended use. Additionally, the compressor features a two-stage design, which increases its efficiency and output, allowing for faster recovery times between cycles.

The Northern Industrial Tools 157494 boasts an impressive air delivery rate, providing users with the necessary airflow for high-demand applications. This feature is particularly beneficial for professionals in construction or automotive industries, where quick and reliable air supply is essential. The compressor also comes with a large, easy-to-read pressure gauge that allows users to monitor the output pressure effortlessly, ensuring that they can make real-time adjustments as needed.

In terms of portability, the Northern Industrial Tools 157494 is designed with user convenience in mind. It is equipped with sturdy wheels and a handle, making it easy to transport from one job site to another. This feature is especially valuable for those who need to move the compressor frequently without compromising on stability or balance.

Overall, the Northern Industrial Tools 157494 represents an ideal blend of power, efficiency, and portability. Its advanced technologies, durable construction, and high air delivery make it a leading choice for professionals and hobbyists alike, ensuring that it can meet a wide range of industrial and home improvement tasks with ease and reliability.