Nortec Steam Humidifiers manual Remote Mounting of the Blower Pack

Page 7

4.Put the power leads from the blower pack through this opening as you position the blower pack on top of the RESDELUX humidifier

5.Push the blower pack forward until the locating tabs on the bottom of the blower pack with slots in the top of the RESDELUX push forward to engage.

6.Use two Phillips screws with star washers in the Blower Pack screw support tabs to secure to the RESDELUX unit.

7.Remove the front door and service cover from the RESDELUX humidifier.

8.Connect the power leads for the blower pack to terminal P7 on the RESDELUX control board located next to the capacity adjustment potentiometer.

9.Use the short piece of steam hose and hose clamps supplied with the basic hardware kit to connect the steam cylinder to the blower pack steam distributor.

Installation of the blower pack is now complete. For instructions on mounting the RESDELUX humidifier please see the location and mounting section.

Figure #9

Blower Pack Cabinet Assembly

Remote Mounting of the Blower Pack

1.The remote mounted blower pack should be located at least 7’ off the floor to prevent the discharged steam from coming in contact with pedestrian traffic or any obstruction.

2.When installing the remote blower pack, ensure the primary voltage to the RESDELUX has been

switched off at the electrical panel, or that it is unplugged (RESDELUX/C).

3.Find a suitable location for mounting the remote blower pack. The surface should be flat with adequate clearances for the top, side, and front:

Table #1

Clearances of Remote Mounted Blower Pack

Minimum Ceiling

Minimum Side

Minimum frontal

Clearance

Clearance

Clearance

inches (cm)

inches (cm)

inches (cm)

18” (45)

18” (45)

60” (150)

 

 

 

 

 

 

4.Minimum slope of steam hose is 20°. Steam lines longer than 5 ft require condensate trap installation (see Figure #6).

5.RESDELUX blower pack has two teardrop (or keyhole) openings on the back of the cabinet for mounting purposes. They are located 8 ¼” apart, and 1” from the top of the blower pack cabinet.

6.Measure the screw locations and use two #8 screws, 2” long. The screws should be anchored in a standard 2” x 4” wood stud or equivalent to ensure adequate support of the blower pack and connecting steam hose.

7.Remove the 7/8” knockout on the top of the RESDELUX humidifier and insert the closed finger grommet into the opening.

8.Put the power leads from the blower pack through this opening. If the wire leads are not long enough field splice the additional requirement, or get a wire extension kit (P/N 1502326) available from

NORTEC.

Figure #10

Steam Absorption Distances

Steam absorption space size in inches for ambient humidity 30% RH, room temperature and selected steam outputs of RESDELUX humidifier.

H

W

F

0”

Steam Output

F

W

H

4 lbs/hr

36"

12"

12"

6 lbs/hr

42"

16"

18"

8 lbs/hr

48"

18"

18"

- 4 -

Image 7
Contents Installation, Operation Maintenance Troubleshooting Guide Table Of Contents Page Receiving & Unpacking Equipment InstallationPRE-INSTALLATION Checkpoint Humidifier ConfigurationMin Steam Distributor Nozzle in duct locationCabinet Mounting of the Blower Pack Steam Hose InstallationCondensate Hose supplied Blower Pack ConnectionTable #1 Clearances of Remote Mounted Blower Pack Remote Mounting of the Blower PackWater Supply Line PlumbingDrain Line Electrical Requirements for Permanently Connected Resdelux LOW Voltage Control Wiring and InstallationControl Wiring ElectricalResdelux Operation Control InstallationOperation IntroductionSteam Cylinder MaintenanceManual Capacity Adjustment When to Replace the Steam CylinderHOW to Install the Replacement Cylinder HOW to Remove the Steam CylinderExtended Shutdown Mandatory Cleaning of the Drain ValveDiagnostic Procedures Troubleshooting TroubleshootingProcedures and Terms Used Diagnosing L1 N Transformer Item Number Part Number Description Spare Parts List and Exploded View Resdelux21a 21b 21c 13a 13d 13e 13b 13c 11b 11a 12 12a 14a Inspect, Check, Clean, and Adjust all items listed Periodic Maintenance ChecklistLimited Warranty MTH/DAY/YR

Steam Humidifiers specifications

Nortec Steam Humidifiers are recognized for their robust performance and reliability in providing precise humidity control for various applications. These advanced humidification systems utilize state-of-the-art technology to ensure optimal indoor air quality in commercial, industrial, and institutional environments. One of the standout features of Nortec Steam Humidifiers is their ability to produce high-quality steam through an efficient and consistent process.

The humidifiers employ a direct steam generation method, which allows for rapid humidity delivery and precise control over output levels. This is particularly beneficial in settings such as hospitals, laboratories, and manufacturing facilities, where specific humidity levels are critical for operational success. The steam produced is free from impurities and is ideal for various applications, including protecting sensitive equipment, preserving materials, and enhancing comfort for occupants.

Another notable characteristic of these humidifiers is their compact design. Nortec Steam Humidifiers are engineered to occupy minimal space while maintaining high productivity. Furthermore, they are equipped with advanced controls and monitoring systems that enable users to customize settings according to their specific needs. This includes options for modulating steam output according to the changing requirements of the environment.

The humidifiers also feature a user-friendly interface, allowing for easy adjustment and monitoring of system performance. High-precision sensors measure humidity levels accurately, ensuring that the output is consistently matched to the desired set point. Nortec Steam Humidifiers are designed with energy efficiency in mind, using innovative technologies to minimize energy consumption while maximizing steam output.

In terms of maintenance, Nortec provides easy access to key components, ensuring that routine checks and servicing can be completed efficiently. The use of advanced materials in the construction of humidifiers contributes to their durability and long operational lifespan. Integration with building management systems is also possible, allowing for seamless operation within a larger environmental control strategy.

In summary, Nortec Steam Humidifiers stand out in the market due to their innovative technologies, precise humidity control, energy efficiency, and ease of maintenance. These features make them an ideal choice for a wide array of humidification needs, ensuring excellent air quality and comfort in any setting. With their commitment to quality and reliability, Nortec continues to be a leader in the humidification industry.