Nilfisk-ALTO 91WS manual Gasoline Powered Machine Fueling Instructions

Page 19

OPERATING INSTRUCTIONS

TO CHARGE THE MOTIVE POWER BATTERIES (Battery powered machines only)

1.Read the detailed instructions provided on the charger.

2.Be sure all controls are “OFF” and machine is located in an area with good ventilation.

3.Open the top cover. The top cover must remain open during the charging process.

4.Disconnect the machine power supply cable from the battery using thequick disconnect provided.

5.Connect the charger cable to the battery connector.

6.Plug the charger into properly grounded AC outlet. Be sure to verify theoperating voltage of your charger. The chargers supplied with machine operate at 115 VAC @60 HZ or 230 VAC @ 50 HZ.

7.The charger will begin charging the batteries after a short period of time. The charger will shut off automati cally when the charging process is complete.

8.Unplug the charger from the grounded AC outlet before disconnecting the charger from the battery.

9.Disconnect the charger cable from the battery.

10.Check the electrolyte level in the battery after charging. Add distilled water if needed.

11.Reconnect the machine power supply cable to the battery cable.

12.Lower the top cover and perform the pre-start checks before operating the machine.

GASOLINE POWERED MACHINE FUELING INSTRUCTIONS

The fuel tank for gasoline powered machines is located on the engine. The top cover must be opened to access the fuel tank. After opening the top cover, observe the combination fuel cap/gas gauge and check the fuel level to determine if the fuel tank needs to be filled.

TO FILL THE GASOLINE POWERED MACHINE FUEL TANK

WARNING

To prevent possible fire. Never fill fuel tank while the engine is running. Always be sure gasoline container and

sweeper are electrically grounded before dispensing gas. This can be done by permanently attaching an insulated

wire with a battery clip on the end to the gasoline container.

1.Turn the key switch to the “OFF” position.

2.Open the top cover.

3.Observe the level indicated by the gas gauge on the fuel tank cap.

4.Remove the fuel tank cap from the fuel tank and add gasoline as needed.

5.Install the gas cap and lower the hinged top cover.

LP POWERED MACHINE FUELING INSTRUCTIONS

Fueling the LP powered machine is accomplished by removing the empty LP cylinder and replacing it with a full replacement cylinder. Some cylinders are equipped with a fuel level gauge. Check the gauge and change the cylinder when the gauge reads “EMPTY”. See the LP Instructions in this manual for additional information.

WARNING

Improper filling procedures could cause an explosion. Have your LP cylinders filled by qualified personnel.

WARNING

Park the machine in a safe area designated for changing LP fuel tanks. The designated safe area must have

adequate ventilation, must be free from sparks or other sources of ignition.

WARNING

NO SMOKING signs should be posted and enforced. The area must not be in the vicinity of flammables, combustible

materials or high temperature sources such as furnaces or ovens.

WARNING

Always store and transport LP fuel tanks with the safety relief valve in the up position. This will prevent the tank from venting liquid propane in the event the safety relief valve opens due to overpressure in the tank. A properly stored tank will only vent gaseous propane which dissipates much faster than liquid propane.

1-18

American-Lincoln

 

91 WS

Page 18 Page 20
Image 19
Page 18 Page 20
Contents AMERICAN-LINCOLN Table of Contents American-Lincoln Specifications Sweeping System Machine DimensionsOptional Equipment Machine Preparation GAS/LP Powered MachinesMachine Preparation Battery Powered Machines Safety Precautions Safety PrecautionsSafety Precautions Machine Controls Machine Controls KEY SwitchHour Meter Machine Controls Filter Shaker SwitchSide Broom Lift Handle Main Broom AdjustmentMain Broom Lever Hopper Dump Handle Filter Manifold LatchFORWARD/REVERSE Control Handle Rewind Starter Circuit BreakersOperating Instructions Battery Machine OperationGAS/LP Machine Operation To Start LP Powered Sweeper Starting Instructions PRE-START ChecklistTo Start the Battery Powered Sweeper To Start GAS Powered SweeperTo Stop Sweeper To Drive Machine for TransportTo Sweep with Machine To Empty HopperBattery Charging Instructions Post Operation ChecklistTo Fill the Gasoline Powered Machine Fuel Tank Gasoline Powered Machine Fueling InstructionsLP Powered Machine Fueling Instructions To Change LP Tank Machine Storage Gasoline Powered MachinesService Chart 10,19 11,15 Sweeping Guidelines HOW to SweepSweeping Various Types of Debris Main Broom Service InstructionsMain Broom Service Instructions To Adjust the Main Broom Sweep HeightService Instructions To Check the Side Broom Sweep Pattern Side BroomsTo Change the Side Brooms Height AD- Justment To Change the Side Brooms Dust Control Service InstructionsTo Clean the Filter Baffle To Clean the Panel FilterTo Clean Hopper Flap Service InstructionsTo Adjust the Side Flaps Hopper Service InstructionsFuel Filter Service Engine AIR Intake ServiceTo Replace the Forward Drive Belt To Check the Engine OIL LevelTo Replace the Reverse Belt LP Safety Precautions LP GAS System LP GAS ComponentsLP Vapor Withdrawal System LP Fuel Tanks LP ChecklistTo Begin Changing the LP Tank LP Tank CareUSE and Care of LP Tanks Changing LP TanksStandard Metric Torque Values Standard Hardware & Torque ValuesDecimal Metric & Conversion Table SAE Grade Bolt IdentificationAbbreviations Screws Hardware Legend Hardware Legend Hardware Legend Hardware Legend Hardware Legend Screw, HHC M14 x 1.50 x 45mmgr10 Ordering Parts American Lincoln TechnologyAmerican-Lincoln Technology Table of Contents Chapter Part Number Description QTY Frame Parts ListHardware Used Frame Exploded View Covers Parts List Covers Exploded View Part Number Description Wheel Drive Parts ListWheel Drive Exploded View Lower Wheel Drive Parts List Lower Wheel Drive Exploded View Main Broom Parts List Main Broom Exploded View Main Broom Arms Parts List Main Broom Arms Exploded View Right Hand Side Broom Parts List Right Hand Side Broom Exploded View 13 H150Hopper Parts List Hopper Exploded View Filter Shaker Parts List Filter Shaker Exploded View Impeller Parts List Impeller -EXPLODED View Battery Parts List Battery Exploded View Service Parts Engine Parts ListEngine Exploded View Electrical Assembly Battery Parts List Electrical Assembly Battery Exploded View Back Wiring View TOPElectrical Assembly GAS Parts List M1 Relay Electrical Assembly GAS Exploded ViewControl Panel Battery Parts List Control Panel Battery Exploded View Control Panel GAS Parts List Control Panel GAS Exploded View Decals Parts List Decals Exploded View American-Lincoln Decals GAS Exploded View American-Lincoln Technology Table of Contents Chapter Left Hand Side Broom Option Parts List Left Hand Side Broom Option Exploded View LP Option Parts List LP Option Exploded View C0626 Foam Filled Tire OptionWET Sweep Bypass Option Spare Parts Kits Battery Machine Part Number DescriptionMain Broom Options TOP Back Wiring View Schematic & Connection Drawing BatteryOption Schematic & Connection Drawing GASIndex Index Index AMERICAN-LINCOLN

91WS specifications

The Nilfisk-ALTO 91WS is a state-of-the-art waste water vacuum system, designed to tackle both outdoor and indoor cleaning tasks across various industries. This versatile machine is particularly renowned for its impressive suction power, allowing for the effective removal of liquid waste, sludge, and debris in less time and with minimal effort.

One of the key features of the 91WS is its robust construction. Designed with durability in mind, the vacuum has a sturdy chassis and components that are resistant to wear and tear, making it ideal for demanding environments such as construction sites and heavy industry. The unit is also equipped with large wheels, ensuring ease of mobility even when fully loaded.

The 91WS incorporates advanced technology to enhance its performance. Its powerful motor delivers strong suction capabilities, while the innovative filtration system effectively separates solids from liquids, preventing clogging and maintaining optimal efficiency. The vacuum's advanced design also allows for quick and easy emptying, minimizing downtime and boosting productivity.

Another significant characteristic of the Nilfisk-ALTO 91WS is its user-friendly interface. Operators will appreciate the intuitive controls that make it simple to adjust settings and monitor performance. The vacuum is designed for easy maintenance; access to key components is straightforward, ensuring that servicing is efficient, and the machine continues to operate at peak capacity.

The 91WS also features multiple attachment options, allowing users to customize the machine for specific tasks. Whether it's cleaning up after spills or managing waste disposal, the versatility of the attachments ensures that it can handle various cleaning challenges with ease.

Safety is paramount in any industrial environment, and the Nilfisk-ALTO 91WS is designed with several safety features. The integrated float system prevents overflow, and the durable construction of the vacuum ensures that it can withstand rigorous use without posing risks to the operator.

In summary, the Nilfisk-ALTO 91WS is a powerful and versatile waste water vacuum that excels in demanding situations. With its strong performance, advanced technologies, and user-friendly features, it is an ideal solution for any business looking to optimize their cleaning processes while ensuring safety and efficiency.
Top Page Image Contents