PHYSICAL SPECIFICATIONS
A
C
D
B
E
INCLUDED PARTS
•One Polymer Subwoofer Grille
•Six #10 x 1
•Six #10
•Logo Badges
One Pair Black (White & Titanium/Black Models) One Pair Red (White & Titanium/Black Models) One Pair White (White Models Only)
One Pair Titanium (Titanium/Black Models Only)
Subwoofer Physical Specifications
| Nominal Diameter: | 10 in. / 250 mm | |
|
|
|
|
| Overall Diameter (A): | 10.75 in. / 273 mm | |
|
|
|
|
| Mounting Hole Diameter (B): | 8.875 in. / 225 mm | |
|
|
|
|
| Bolt Hole Circle (C): | 9.706 in. / 247 mm | |
|
|
|
|
| Motor Overmold Outer Diameter (D): | 6.11 in. / 155 mm | |
|
|
|
|
| Mounting Depth (E): | 5.93 in. / 151 mm | |
|
|
|
|
| Net Weight: | 11.4 lbs. / 5.17 Kg | |
|
|
|
|
| Driver Displacement: | 0.064 ft3 / 1.81 litres | |
|
|
|
|
|
|
|
|
| Subwoofer Parameters | M10IB5 | M10W5 |
|
|
|
|
| Free Air Resonance (Fs): | 42.20 Hz | 31.55 Hz |
|
|
|
|
| Electrical “Q” (Qes): | 0.819 | 0.484 |
|
|
|
|
| Mechanical “Q” (Qms): | 10.355 | 8.946 |
|
|
|
|
| Total Speaker “Q” (Qts): | 0.759 | 0.460 |
|
|
|
|
| Equivalent Compliance (Vas): | 1.16 ft3 / 32.85 litres | 1.58 ft3 / 44.75 litres |
|
|
|
|
| 0.52 in. / 13.2 mm | 0.52 in. / 13.2 mm | |
|
|
|
|
| Efficiency (1W/1m)**: | 86.8 dB SPL | 86.7 dB SPL |
|
|
|
|
| Effective Piston Area (Sd): | 50.11 in² / 0.0323 m² | 50.11 in² / 0.0323 m² |
|
|
|
|
| DC Resistance (Re): | 4.167 ohm | 3.602 ohm |
|
|
|
|
| Nominal Impedance: | 4 ohm | 4 ohm |
|
|
|
|
| Infinite Baffle Use: | Yes | No |
|
|
|
|
| Enclosure Use: | Yes (Sealed Only) | Yes (Sealed and Ported) |
|
|
|
|
| Power Handling (continuous): | 250W | 250W |
|
|
|
|
*Xmax specifications are derived via
**Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder” !
We recommend the use of this speaker in a
INSTALLATION PROCEDURE
The diagram above shows the typical installation procedure into a fiberglass panel using the supplied hardware (Classic Grille Model shown. Installation is the same for Sport Grille Models). Always follow proper safety procedures when working on a vessel. Use
1)Choose a flat mounting surface that has sufficient depth and air space behind it to accept the subwoofer.
2)Cut a
3)Run the speaker cable to the mounting location.
4)Place the woofer in the hole and mark the screw hole locations using a sharp, pointed tool.
5)Remove the woofer and drill a pilot hole (see chart on next page) in each of the screw locations. It is also advisable to use a
6)Connect the speaker wires and place the woofer, with its grille in place, into the opening (for Sport Grille models, pay attention to where the logo badge will added.
7)While holding the speaker firmly in its mounting location, evenly snug the mounting screws in a
2 | A l l s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e . | JL AUDIO M10IB5/M10W5 |