Husqvarna 540200800 system manual Attaching a Spindle Drive Assembly

Page 11

Operators Guide

Assembly Instructions (continued)

5. Attaching a Spindle Drive Assembly

1.Remove the discharge chute.

2.Remove the right hand belt shield.

3.Remove the deck belt from the right spindle assembly sheave.

4.Remove this sheave but keep the ¼” square key and the two washers at hand for reinstal- lation.

5.Install the Stepped Sheave and spacer/key retainer included in the kit using the original key and washers but substituting the original 7/16” HCS with the longer version provided. An application of anti-seize is recommended.

6.Reinstall the deck belt.

7.The 5/8” hole toward the rear of the ¼” thick discharge chute mounting bar at the right end of the deck may be distorted from forming or loaded with paint. Drill out or fill this hole until it will accept a 5/8” bolt or piece of bar stock. Keep the fit close.

8.If any weld beads or the edge of the deck top project past the right end surface of the deck, these must be ground back to allow the fan assembly to fit up flush to the end of the deck.

9.Remove the 3/8” fastener, nut, and clamp from the inside front corner of the fan assembly.

10.Remove the sheave floor to expose the fan assembly belt sheave from below.

11.Loosen the nut retaining the belt guide/retainer, install the belt from the Drive Kit, retighten the nut, verify the belt clears the guide, and reinstall the sheave floor.

12.Rest the fan assembly onto the deck end and slide the pilot thru the 5/8” hole previously mentioned so that fan assembly is supported by the pilot and the ¼” stop block welded under the clamp at the front of the fan assembly.

Note: It may be necessary to swing the idler pulley away from the assembly mounting face to clear the chute mounting bar and the discharge chute mounting tab on the deck.

13.Reinstall the clamp at the front of the assembly so that the tab at the lower end of the clamp passes thru the rectangular slot at the right front corner of the mower deck, but leave the fastener loose to ease belt installation.

14.Rotate the belt idler as far forward as possible and install the belt over the top groove of the new deck sheave.

15.Tighten the clamp fastener.

16.Using a scribe or other small sharp object, transfer the mounting hole location at the rear edge of the fan assembly onto the mating vertical surface at the right rear of the mower deck and drill thru with a 25/64” drill.

17.Install the stops on the deck stop pins located at the rear of the deck then install the new belt shield.

18.Install the tube support to the main collection assembly using the 3/8” fastener provided, po- sitioning so that the tube is 2” to 3” away from the tire.

19.Install the 7” hose to the fan assembly and the container input port using the hose clamps provided.

20.Clamp the tube to the tube support.

11

Image 11
Contents Z2-7 Collection System Operator’s Manual Models Parts Manual Index Operators Guide SpecificationsFeatures and Controls Auxiliary Engine Features and Controls Spindle Drive General Information Operation Unpacking Instructions Assembly InstructionsAttaching the Heat Shield If installing a spindle drive assembly, skip to stepAttaching the Engine Mount and Vacuum Assembly Attaching a Spindle Drive Assembly Hose Attachment Operating the Vacuum Auxiliary Engine Vacuum Assembly Servicing the EnginePre-Start Check Starting the EngineStorage Cleaning and WashingPreventative Maintenance Schedule Caring For Vacuum Hoses Engine Service and MaintenanceCleaning Exhaust Screen Trouble Shooting Guide Assembly Replacement Parts540200853 Top/Frame Assembly Top Assembly Replacement Parts QTY Description Spindle Drive KitDescription QTY Accessories, Auxiliary EngineBoot for Gen Boot for Gen II 72 Deck Hitch Custom Kit for MiniCustom Kit for Gen Custom Kit for Gen II 72 Deck Custom Kit for Gen Custom Kit for iZ Spindle Drive Fan Assembly FAN Cover W/DECALS

540200800 specifications

The Husqvarna 540200800 is a versatile and powerful tool designed for professional landscapers and outdoor enthusiasts alike. This innovative product, a part of Husqvarna's high-quality line-up, stands out due to its combination of advanced features and user-friendly design.

One of the key features of the Husqvarna 540200800 is its robust motor, which delivers ample power for a variety of tasks, from trimming and pruning to heavy-duty cutting. This high-performance engine allows for efficient operation, ensuring that users can complete their jobs quickly and effectively.

The design of the Husqvarna 540200800 emphasizes ergonomics, making it comfortable to operate for extended periods. The adjustable handle allows users to modify the angle and length to suit their height and working style, reducing fatigue during long sessions. Additionally, the lightweight structure ensures maneuverability, allowing users to navigate through tight spaces with ease.

Husqvarna has incorporated several cutting-edge technologies into the 540200800, enhancing its performance and reliability. The X-Torq engine technology significantly reduces fuel consumption and emissions, making it more environmentally friendly while ensuring that users can operate for longer without frequent refueling. Furthermore, the Smart Start feature ensures hassle-free starting, minimizing the effort needed to get the machine up and running.

Another notable characteristic of the Husqvarna 540200800 is its durability. Built with high-quality materials and engineered for tough outdoor conditions, this tool is designed to withstand demanding use. Its rugged construction ensures longevity, making it a sound investment for professional users who rely on their equipment day in and day out.

The Husqvarna 540200800 also features a variety of attachments that can be easily swapped out, making it an adaptable tool for various tasks. From edging to blowing, this system allows for efficient handling of different landscaping jobs without the need for multiple pieces of equipment.

In summary, the Husqvarna 540200800 is a top-tier tool that combines power, versatility, and user-friendly design. Its advanced technologies, high-performance engine, and ergonomic features make it an essential asset for anyone looking to maintain a pristine outdoor space. With this tool in hand, users can expect exceptional results and a smoother workflow, whether for personal use or professional landscaping.