Herrmidifier Co G-200/300 manual To Inspect and Replace the Evaporator Pad

Page 10

Maintenance

To Inspect and Replace the Evaporator Pad:

It is recommended that the evaporator pad in the humidifier be replaced annually to maintain efficient operation. However, more frequent replacement may be necessary in areas of poor water quality.

1.Disconnect the power supply to the furnace.Turn OFF the water supply at the saddle valve by turning the valve handle clockwise.

2.Fully loosen the thumb screw at the bottom of the unit cover. The screw will remain attached to the cover. To remove the cover from the duct, pull the bottom away and then lift up. Put the cover aside for reassembly.

3.Remove the water distribution tray, located above the evaporator pad. It is held in place by a snap that must be lifted to pull out the tray.

4.Pull the evaporator pad and frame assembly away from the duct, being careful not to disturb the drain connection. Remove the old evaporator pad and discard.

5.Inspect the interior of the humidifier and remove any mineral deposits and accumulation from the frame assembly and drain tray.

6.Remove the new evaporator pad from the plastic bag and insert into the frame assembly, with the black spot facing up. Ensure that no part of the evaporator pad is outside of the frame. Return the evaporator pad and frame assembly to their original position inside the humidifier.

7.Check the distribution tray to ensure that holes are clear of any scale build up. If desired, the distribution tray can be washed with mild detergent and warm water.

8.Replace the distribution tray making sure the snap is hooked over the outside edge of the tray. Replace the cover and secure by tightening the thumb screw. Turn the water back on and reconnect power to the furnace.

End of Heating Season Shut Down:

1.Inspect and clean humidifier and components.

2.Turn water supply off at the solenoid valve.

3.Turn humidistat off.

4.Close the bypass damper if installed.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 200/300 Duct Mount Bypass Humidifier Table of Contents Introduction IntroductionSpecifications SpecificationsOperation This chart uses A.R.I. standard designationsCapacity Selection Guide Air Tightness of HomeRecommended Relative Humidity Levels Vs. Temperature Start UpInstallation Mounting Locations To Inspect and Clean the Conical Mesh Water Filter MaintenanceMaintenance of Your Humidifier To Inspect and Clean the Fluid RestrictorTo Inspect and Replace the Evaporator Pad End of Heating Season Shut DownTroubleshooting Humidifier is running all the time. Is this normal?Troubleshooting Description of Parts Parts list Description Model G-200 300Unit Diagram Warranty Humidifier Limited Two Year Warranty

G-200/300 specifications

The Herrmidifier Co G-200/300 is an advanced humidification solution designed for both commercial and residential applications, ensuring optimal indoor air quality and comfort. This innovative system stands out in the market due to its modern technologies and superior features that address the needs of today's environment.

One of the standout features of the G-200/300 is its high-capacity output, which can efficiently manage humidity levels across larger spaces. With a robust humidifying capacity, it caters to diverse environments, from offices and retail spaces to residential areas, providing a comfortable atmosphere for occupants. Its adjustable settings allow users to customize humidity levels according to personal preferences or specific requirements, ensuring a personalized experience.

The G-200/300 employs an advanced microprocessor control system that simplifies operation and enhances efficiency. This system allows for precise monitoring and adjustment of humidity levels, making it easier for users to maintain optimal conditions without manual intervention. Additionally, the unit’s digital display provides real-time feedback on performance metrics, such as humidity levels, temperature, and operational status, ensuring informed decision-making.

Energy efficiency is another hallmark of the Herrmidifier G-200/300. Designed with energy-saving technologies, it minimizes power consumption while maximizing performance. This results in lower utility costs and a more sustainable operation. The unit's low-water shutdown feature further enhances safety by automatically turning off the system if the water supply is low, preventing damage and ensuring longevity.

The design of the G-200/300 also emphasizes user-friendly maintenance. It features easy-access components for straightforward cleaning and servicing, which helps to maintain peak performance and extend the lifespan of the unit. The filter system is designed for easy replacement, ensuring that the air remains fresh and free from contaminants.

Constructed from high-quality materials, the Herrmidifier G-200/300 is built to withstand the rigors of daily use, making it a reliable addition to any environment. Its sleek design allows it to blend seamlessly with various decors, while its compact size ensures it can be placed in areas with limited space.

In conclusion, the Herrmidifier Co G-200/300 represents a leap forward in humidification technology. With its high capacity, advanced controls, energy efficiency, and user-friendly design, it stands as an excellent choice for anyone looking to enhance indoor air quality and comfort. This system effectively meets the diverse needs of modern users, making it a valuable investment for both personal and professional spaces.
Top Page Image Contents