GSW 61009 REV. C (09-03) manual Water Temperature Regulation, Burner Maintenance, Gas Control

Page 13

Special note on propane fuel:

DANGER

Explosion Hazard

To clear accumulated LP gas before attempt- ing to light or re-light pilot:

•Open burner door by loosening the two mounting screws and pulling door back approximately 1/2” away from combustion chamber.

•Allow ventilation of combustion chamber for ten minutes.

•Close burner door. Refer to warning

below.

Failure to do so can result in death, explosion, or fire.

L.P. GAS IS HEAVIER THAN AIR

Should there be a leak in the system, the gas will settle at FLOOR LEVEL. Basements, crawl spaces, closets and areas below ground level will serve as pockets for the accumulation of the gas.

Out of fuel

When your L.P. tank runs out of fuel, turn off gas at all gas appliances. After L.P. tank is refilled, all appliances must be re-lit according to the manufacturers instructions.

Water Temperature Regulation

The thermostat is adjusted to its lowest temperature posi- tion when shipped from the factory. The temperature of the water can be selected by setting of the temperature dial. The “LOW” position on the thermostat is the preferred start- ing point for setting the temperature/control knob (approxi- mately 50°C (120°F)). The lowest setting will maintain the minimum water temperature if you are going away for an extended period. The burner may be extinguished if operat-

DANGER

Explosion Hazard

Tighten both manifold door screws securely. Remove any fiberglass between gasket and combustion chamber.

Replace view port if glass is missing or damaged.

Replace door gasket if damaged.

Failure to do so can result in death, explosion, or fire.

ed below this temperature.

Energy conservation is a consideration when selecting the water temperature setting.

HIGHER SETTING INCREASES THE RISK OF SCALD INJURY

In households with children or invalids and/or elderly per- sons, select a lower temperature setting. To reduce the risk of scalding, valves for reducing the point of discharge water temperature by mixing in branch water lines are available. Please consult a licensed plumber or plumbing authority.

Exposure to water

IMPORTANT:

Should the water heater be subjected to flooding, fire, or other unusual condition, turn off gas at the manual gas shut-off valve and water at the inlet valve to the heater. Do not put the heater in operation until it has been thorough- ly checked by a qualified gas technician.

Tampering

Tampering with the thermostat, gas valve or temperature pressure relief valve is DANGEROUS and voids all war- ranties. Only qualified personnel should service these com- ponents.

Burner Maintenance

At least every three (3) months, check the burner and pilot flames. The burner flames must be a soft blue flame with no yellow tips. Yellow tips indicate a carbonizing flame which can, depending on severity, deposit carbon (soot) on the combustion chamber and flue passages. A sheet metal burner is used on natural gas models (see Figure 4).

The sheet metal burner for Natural Gas has no external air adjustment. It is fully self-compensating and no outside adjustment is required. Observe the flame pattern. Ensure that no debris has fallen on top of the burner and no foreign objects have been introduced into the combustion chamber. Ensure that the vent terminal openings are not obstructed and the inner door to the combustion chamber is closed.

Gas Control

For gas control replacement, contact your local gas utility, or a qualified serviceman. The replacement control must be a manufacturer’s approved replacement for the control which has been removed.

Figure 4

– 13 –

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if YOU Smell GAS For Your SafetyMaintenance Instructions Table of ContentsIntroduction II SafetyConsumer Responsibilities Safety Warning Scalding Safety Warning Flammable VapoursValves For Hot Water Supply Systems, Ansi Z21.22/CSA III Installation Venting Installation ComponentsLocating Clearance Hole For Vent Vent connectionsCondition Offset vent pipe arrangementWater Piping Gas ConnectionsHigh rise vent pipe arrangement Installation Checklist Temperature & Pressure Relief ValveDischarge line Closed system/Thermal expansionLighting instructions Robertshaw 110R IV Operating InstructionsFigure a Lighting instructions White-Rodgers 37CBurner Maintenance Water Temperature RegulationGas Control Tank Maintenance Instructions General HousekeepingVenting System Inspection ControlVI Combo Heating What this Warranty does not Cover Limited WarrantyWHO is Covered HOW the Original Owner can Make a Warranty Claim

61009 REV. C (09-03) specifications

The GSW 61009 REV. C (09-03) is a prominent model within the realm of electrical distribution and protection equipment, specifically engineered to deliver reliable performance in various industrial applications. This device is particularly tailored for low-voltage electrical networks, ensuring safety, efficiency, and longevity in operations.

One of the main features of the GSW 61009 REV. C is its advanced circuit protection capabilities. Equipped with residual current devices (RCDs), it is designed to prevent electric shocks and electrical fires, enhancing overall safety standards in any installation. The device also incorporates circuit breakers that automatically disconnect electrical circuits during overloads or short circuits, preventing potential equipment damage and safeguarding personnel.

The GSW 61009 REV. C also exhibits exceptional thermal and mechanical stability, attributed to its high-quality materials and robust engineering. It is built to withstand harsh operational environments, ensuring reliable functionality even under challenging conditions. This durability is crucial for industries such as manufacturing, construction, and energy sectors, where equipment often faces extreme temperatures and vibrations.

Technologically, the GSW 61009 REV. C is designed with user-friendly features, making installation and maintenance straightforward for technicians. It includes clear labeling and intuitive interfaces for easy operation, which simplifies the process of monitoring and troubleshooting. Furthermore, its modular design allows for easy upgrades and expansions, accommodating evolving electrical needs without the need for a complete system overhaul.

The GSW 61009 REV. C also complies with international safety standards, ensuring that it meets rigorous guidelines for electrical devices. This certification not only reinforces the product’s reliability but also builds trust with end-users aware of safety compliance in electrical installations.

Additionally, energy efficiency is a priority with the GSW 61009 REV. C, as it minimizes power loss during operation, contributing to lower energy costs. This focus on efficiency aligns with global sustainability efforts, positioning the product as a responsible choice for modern electrical applications.

In summary, the GSW 61009 REV. C (09-03) stands out as an essential component in electrical systems, offering optimal protection, durability, and efficiency. Its features and technologies make it a preferred choice for industries requiring robust and reliable electrical distribution solutions. The combination of safety, ease of use, and compliance with standards underscores its importance in safeguarding both people and infrastructure in the electrical landscape.
Top Page Image Contents