Danby DDR586R Manual | Dehumidifier Instructions & Settings

Circuit d’alimentation électrique - Spécifications

Operating Instructions

1.Tout câblage doit être réalisé par un électricien qualifié, en conformité avec les prescriptions des\ codes national et local régissant les installations électriques. Pour toute question au sujet des instru tions qui suivent, contacter un électricien qualifié.

2.AVANT l’installation et AVANT l’utilisation de cet appareil, contrôler les caractéristiques de la source d’électricité, et résoudre tout problème affectant le câblage.

3.Pour la sécurité et la protection des utilisateurs, cet appareil est mis à la terre lorsqu’il est branché sur une prise de courant de même configuration que la fiche de branchement. En cas de doute quant à la qualité de la mise à la terre de la prise de courant, consulter un électricien qualifié. NE JAMAIS UTILISER UN CÂBLE DE RALLONGE NI UN ADAPTATEUR SI LA CONFIGURATION DE LA FICHE DE BRANCHEMENT NE CORRESPOND PAS À CELLE DE LA PRISE DE COURANT.

4.La plaque signalétique de l’appareil est située sur la paroi (arrière) du cabinet. On y trouve les caractéristiques électriques et techniques spécifiques de cet appareil.

5.Pour éviter les risques de blessures corporelles, on doit toujours débrancher l’appareil de la source d’électricité avant d’entreprendre des travaux de nettoyage ou d’entretien.

Spécifications de l’appareil:		DDR586R
	Capacité de déshumidification (Pintes/Litres)	58/ 27,44

	Alimentation électrique	115 Volts / 60 Hz

	Consommation d’énergie (watts)	762

	Intensité nominale

	• Déshumidification	6,63

	Circulation d’air – Vitesse de ventilateur haute / basse (pi. cu. /min)(L/min)	178,5 / 145

	Type de réfrigérant	R22

	Capacité du réservoir d’eau (litres / pintes)	5,3 / 11,2

	Niveau de bruit en fonctionnement (dB A)	50

	Dimensions (largeur/hauteur/profondeur)	13-3/4 po x 30-1/2 po x 13-3/16 po

	Poids net (kg/lb)	25 / 55,1

NOTE: Les spécifications sont sujettes aux changements sans préavis (pour l'amélioration des produits).

Factory Default Setting:

When the unit is first connected to a power supply, the electronic circuit board will automatically default to the following factory settings;

Mode: Dehumidifier

Humidity Set Air Value:60% RH

Fan Speed: = Low

NOTE: In the event of a power failure or the unit is switched ‘Off’, the most recent settings are retained and restored once the power is switched “On”/resumed.

IMPORTANT NOTE: Depending on the ambient humidity conditions, when power is restored or switched ‘On’ the dehumidifier may not start automatically under the factory or custom (see page 7) default setting. This is an indica- tion that the ambient RH% level of the surrounding envi- ronment is lower than the current default setting and it may be necessary to select a lower set RH% value.

DRY MODE SELECTION:

1.The unit does not have to be switched on (opera- tional) to select/set a program. All programs can be selected with the unit in the “off” position.

2.Press the MODE button until the Dry symbol is shown in the mode area of the display.

Note: Each time the MODE button is pressed, the setting will alternate between DRY (dehumidifier) and FAN (only) mode.

3.Press the or cursor buttons to select the

desired RH% operating value. To select CONTINUOUS

operation, press the button until the symbol “- -” appears in the SET AIR display. During CONTINUOUS mode operation, the humidistat (control) will be by-passed and the compressor will operate non-stop regardless of humidity conditions.

FAN SPEED SELECTION:

4.Press the fan symbol on the keypad. Each time the button is pressed, the mode selection will alternate between "High Fan" and "Low Fan" speed options. The fan speed you select will appear in the LED display; either a 4 blade fan symbol for ‘high fan’ or a 3 blade fan symbol for ‘low fan’ will be shown in the display area.

5.When all settings are complete, press the I/O button to start the selected operation (MODE) and the blue opera- tion light will illuminate.

FAN ONLY MODE SELECTION:

1.Press the MODE button until the fan blade symbol is shown in the mode area of the display.

2.Press the "Fan” symbol on the keypad. Each time the button is pressed, the mode selection will alternate between "High Fan" and "Low Fan" speed options.

3.When all settings are complete, press the on/off button to start fan mode operation and the blue operation light will illuminate.

AIR FILTER:

Your dehumidifier features a removable Air Filter. This fil- ter is located at the front of the unit (behind the front air intake grill) The air filter plays an important role in helping to reduce (minimize) dust/dirt particles from the surround- ing environment. A blocked/clogged air filter reduces air flow impacting negatively on operating efficiency. To main- tain maximum operating efficiency; The filter must

be checked and cleaned regularly. (every 2 weeks) More frequent cleaning may be required depending upon indoor air quality.

IMPORTANT: Never operate the unit without the air filter in place.

AIR FILTER REMOVAL:

1.Locate the air filter (handle) tab on the upper right side of the front air intake grill and slide-out the filter to the right.

2.Clean the filter thoroughly using a vacuum cleaner or wash using luke warm water and mild detergent. Dry thoroughly before re-installing.

3.To re-install the air filter, slide the filter back inside

the tracks until it snaps (locks) into position.

DDR586R specifications

The Danby DDR586R is a highly efficient dehumidifier designed to create a comfortable living environment by regulating humidity levels in your home. With a capacity of 58 pints, this unit is suitable for medium to large spaces, making it ideal for basements, living rooms, or other areas prone to excess moisture.

One of the standout features of the DDR586R is its Energy Star certification, which signifies its energy efficiency. This means it not only effectively removes moisture from the air but does so while minimizing electricity consumption. This is particularly important for homeowners seeking to lower their energy bills while maintaining a healthy indoor environment.

The Danby DDR586R employs advanced technology to optimize its performance. It features a modern rotary compressor that enhances operational efficiency and ensures quieter performance compared to traditional models. This means users can enjoy the benefits of a dehumidifier without the disruptive noise often associated with older units.

Another notable characteristic is the continuous drainage option, allowing for uninterrupted operation. Users can connect a standard garden hose to the unit, enabling it to drain water automatically. This feature is especially useful for individuals who may forget to regularly empty the water reservoir, which can hold up to 13.5 liters of moisture before needing to be emptied manually.

The built-in humidistat offers the convenience of setting your desired humidity level, allowing the DDR586R to automatically turn on and off as needed to maintain optimal conditions. This not only enhances comfort but also protects against mold and mildew growth, preserving your home's structural integrity and indoor air quality.

The compact design and integrated handles make the Danby DDR586R easy to move from room to room, allowing for personalized humidity control wherever it’s needed. Additionally, the unit’s filter is easily accessible and washable, ensuring that maintenance is hassle-free.

With its combination of efficiency, advanced technology, and user-friendly features, the Danby DDR586R is an excellent investment for anyone looking to improve indoor air quality and reduce excess moisture in their home. Whether you're dealing with a damp basement or simply seeking to maintain comfortable humidity levels, this dehumidifier offers the reliability and performance you need.