Danby DDR586R Remote Control Features, Batteries should be replaced when, Battery replacement

Page 9

Fonctions des touches du tableau de commande électronique :

3

4

 

1

2

5

Remote Control Features

The hand held remote unit allows you to control all operational aspects of your dehumidifer from the convenience of your favorite armchair. Here are some things you should know about operating the unit with the hand held remote.

Control Buttons

I/O: Power switch (On/Off).

MODE: Selects the required operating mode (Dehumidifier / Fan ).

:Selects the fan speed settings (HIGH FAN / LOW FAN).

Each time the button is pressed will alternate

between HI FAN and LOW FAN speed.

Touche I/O : À chaque fois que cette commande est pressée, l’appareil se met en marche ou s’éteint.

Touche Ventilateur :

Àchaque fois que cette commande est pressée, la vitesse du ventilateur alternera entre haute et basse.

Touche Minutrie : Utilisée pour amorcer une mise en service temporisée et/ou une mise hors de serv- ice temporisée. Appuyer sur le bouton tandis que l'unité n’est pas en marche vous permettra de plac- er le temporisateur retardé (début). Appuyer sur le bouton quand l'unité est en marche vous permettra de placer le temporisateur retardé (d'arrêt).

Cette touche vous permet de réduire les réglages d’humidité relative ou minutrie. Avec chaque pres- sion sur la touche durant;

Minutrie: réduira en incréments de 1,0 - de 24,0 heures à 10,0 heures puis par 0.5 - de 10,0 heures à 0,5 heures.

Sec: la valeur SET RH% réduira par 5% (les valeurs réglables sont entre 80% et 35%).

Cette touche vous permet d’augmenter les réglages d’humidité relative ou minutrie. Avec chaque pres- sion sur la touche durant;

Minutrie: augmentera en incréments de 0,5 - de 0,5 heures à 10,0 heures puis par 1,0 - de 10,0 heures à 24,0 heures.

Sec: la valeur SET RH% augmentera par 5% (les valeurs réglables sont entre 35% et 80%).

Touche Mode : À chaque fois que cette commande est pressée, le mode de fonctionnement alternera entre déshumidificateur et ventilateur. Le symbole pour la mode choisi apparaîtra sur l’écran d’affichage à diodes.

AFFICHAGE À DIODES : L’écran d’affichage indique l’in- formation suivante :

1.Conditions actuelles ambiantes du % d’humidité relative de la pièce.

2.La valeur de fonctionnement réglée du % d’humidité relative.

3.Le mode de fonctionnement choisi;

Sec Ventilateur

4.La vitesse du ventilateur choisi;

Haute Basse

5.L’heure choisie de la mise en service / hors de service temporisée;

En Marche

Arrêt

0.0 Réglage

 

 

du

 

 

Minutrie

Used to adjust (decrease) relative humidity settings. Each time the button is pressed the SET RH% value will decrease by 5% (adjustable values between 80% ~ 35%) This button can also be used to decrease the auto timed (delay start / delayed stop) programs.

0.5hr increments (from 0.5 hrs. ~ 10hrs.)

1.0hr increments (from 10hrs. ~ 24hrs.)

Used to adjust (increase) relative humidity settings. Each time the button is pressed the SET RH% value will increase by 5% (adjustable values between 35% ~ 80%) This button can also be used to increase the auto timed (delay start / delayed stop) programs.

0.5hr increments (from 0.5 hrs. ~ 10hrs.)

1.0hr increments (from 10hrs. ~ 24hrs.)

Used to initiate a delayed start “on” time and/or delayed stop “off” time.

ºF / ºC Used to switch temperature readings (LED readout display) from Celsius to Fahrenheit. Each time button is pressed will alternate between both temperature scales.

To operate the hand held remote control will require two “AAA”(1.5 volt) Alkaline batteries (included ).

Batteries should be replaced when:

a)No signal (beep) is heard from the main unit when pressing the buttons on the remote control while attempting to program the main unit.

b)The main unit does not respond to the any of the commands issued by the remote control unit.

Battery replacement:

1.Open the rear cover on the backside of the remote control unit in the direction of the arrow. Continue pulling (gently) until the cover separates completely from the unit.

2.Replace the (2) batteries “AAA” (1.5 volts) follow- ing the same orientation (polarity) as depicted inside the battery chamber.(+/-)

3.Re-install lower cover.

4.If the remote control will not be used for extended periods of time (vacations etc.), batteries should be removed.

The remote operates within a range of 7 meters

(23 ft.) from the receiver located inside the main unit. Any obstruction between the receiver and remote may cause signal interference, limiting the ability to program the main unit.

19

8

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model Modèle DDR586RGarantie Limitée DE Produit Table Of ContentsIntroduction This symbol denotes a caution or warningSoins et entretien RemisageOrifice DE Drainage Direct Choix DU Mode DE Déshumidification SEC Instructions d’utilisation Electrical SpecificationsDDR586R Réglage implicite de l’usineInstallation FeaturesChoix de l’emplacement Unit Parts IdentificationFonction des témoins lumineux Fonctionnement du réservoir d’eauRéglage implicite modifié par utilisateur Indicator Light Function Caractéristiques de télécommandeRemplacement des piles Les piles devraient être remplacées quandBattery replacement Remote Control FeaturesBatteries should be replaced when Touche VentilateurPièces de l’appareil CaractéristiquesLocation Operating Instructions Connecting the Direct Drain Direct Drain FeatureStorage Direct DrainMise EN Garde Ce symbole représente une mise en garde ou un avertissementTable des matières Limited Product Warranty

DDR586R specifications

The Danby DDR586R is a highly efficient dehumidifier designed to create a comfortable living environment by regulating humidity levels in your home. With a capacity of 58 pints, this unit is suitable for medium to large spaces, making it ideal for basements, living rooms, or other areas prone to excess moisture.

One of the standout features of the DDR586R is its Energy Star certification, which signifies its energy efficiency. This means it not only effectively removes moisture from the air but does so while minimizing electricity consumption. This is particularly important for homeowners seeking to lower their energy bills while maintaining a healthy indoor environment.

The Danby DDR586R employs advanced technology to optimize its performance. It features a modern rotary compressor that enhances operational efficiency and ensures quieter performance compared to traditional models. This means users can enjoy the benefits of a dehumidifier without the disruptive noise often associated with older units.

Another notable characteristic is the continuous drainage option, allowing for uninterrupted operation. Users can connect a standard garden hose to the unit, enabling it to drain water automatically. This feature is especially useful for individuals who may forget to regularly empty the water reservoir, which can hold up to 13.5 liters of moisture before needing to be emptied manually.

The built-in humidistat offers the convenience of setting your desired humidity level, allowing the DDR586R to automatically turn on and off as needed to maintain optimal conditions. This not only enhances comfort but also protects against mold and mildew growth, preserving your home's structural integrity and indoor air quality.

The compact design and integrated handles make the Danby DDR586R easy to move from room to room, allowing for personalized humidity control wherever it’s needed. Additionally, the unit’s filter is easily accessible and washable, ensuring that maintenance is hassle-free.

With its combination of efficiency, advanced technology, and user-friendly features, the Danby DDR586R is an excellent investment for anyone looking to improve indoor air quality and reduce excess moisture in their home. Whether you're dealing with a damp basement or simply seeking to maintain comfortable humidity levels, this dehumidifier offers the reliability and performance you need.
Top Page Image Contents