Windsor 10052460, SG32, SG36, SG28, 10052450, 10052470 Squeegee Adjustment, To Adjust Squeegee Pitch

Page 28

MAINTENANCE

3. SQUEEGEE ADJUSTMENT

Adjusting the squeegee is a two-part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The pitch adjustment is facilitated by the use of a spirit level mounted on the squeegee tool. The second adjustment is the amount of deflection or down pressure on the squeegee.

TO ADJUST SQUEEGEE PITCH

1.Choose a smooth, level surface. Turn on the key switch, release the machine parking brake, lower the squeegee and drive forward at least 2 feet (60 cm).

2.With the squeegee down, stop the machine and set the parking brake. Do not allow the machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across tool. This should correspond to the bubble being in the middle position of the spirit level.

4.To decrease the deflection of the squeegee blade at the ends, turn knob on squeegee trailing arm clockwise. To increase the deflection at the ends of the squeegee assembly, turn knob counter clockwise.

5.Again check the deflection of the squeegee blades. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade.

TO ADJUST SQUEEGEE DEFLECTION

3/8”

PROPER DEFLECTION OF SQUEEGEE BLADE

1.Choose a smooth, level surface. Lower the squeegee and drive forward at least 2 feet.

2.With the squeegee down, stop the machine and set the parking brake. Do not allow the machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Observe the amount of squeegee deflection. It should deflect 3/8in (9.5 mm) across the entire width of the squeegee.

4.To increase the squeegee defection, turn the knobs over the squeegee floor wheels counterclockwise. To decrease the squeegee defection turn the knob over the squeegee floor wheels clockwise. Each knob can be adjusted separately to insure that the blade curls evenly from end to end.

5.Turn on the key switch, release the parking brake. Raise, then lower squeegee assembly. Drive forward at least 2 feet.

6.Repeat steps 2 through 5 until deflection of 3/8 in (9.5 mm) is reached.

4-5

86037580 GLIDE 01/03/07

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents HOW to USE this Manual Parts ListImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency Stop ButtonONE Touch Switch Brush Pressure SwitchSolution Control Switch VACUUM/SQUEEGEE SwitchDisplay Toggle Switch Information Display -SCREENScrub Deck Shift Switch 36 in only Recycle Indicator Light Optional Recycle Switch OptionalHeadlight Switch Optional Directional Control Pedal and Speed Reduction Feature Speed Reduction FeatureBrake Pedal Parking Brake LeverSeat Adjustment Grab BAR Squeegee Camber Adjustment KnobSqueegee Defection Adjustment Knob Side Squeegee Defection Adjustment KnobMachine Operation PRE-RUN Machine InspectionStarting Machine Filling the MachineEmergency Stop Procedure To Begin ScrubbingTo Stop Scrubbing Double ScrubEmptying and Cleaning Tanks Recovery Tank Solution TankMaintenance Battery Maintenance BatteriesLOW Battery SHUT-DOWN To Charge BatteriesTo Remove Batteries Battery Tray Drain HoseTo Replace Batteries Squeegee Adjustment To Adjust Squeegee PitchTo Replace or Rotate Rear Squeegee Blades To Remove Squeegee AssemblyTo Replace or Rotate Front Squeegee Blades Side Squeegee Adjustment Adjusting the Side Squeegee DeflectionReplacing or Installing Scrub Brushes Scrub BrushesUncoated Floors Finished FloorsFloat Switch Solution StrainerBrake Adjustment Steering Chain Tensioner AdjustmentVacuum Motor Changing Vacuum MotorBrush Motor Brush Motor Carbon Brush ReplacementChanging Brush Motors Traction Motor Traction Motor Carbon Brush ReplacmentFuse Circuit BreakersSqueegee Actuator REMOVAL/REPLACEMENT Squeegee Actuator AdjustmentScrub Deck Actuator REMOVAL/REPLACEMENT Scrub Deck Actuator AdjustmentTransporting Machine Towing or Pushing MachineMachine TIE-DOWNS Preparation for TransportingJacking Machine Machine JackingTo Jack UP Machine Machine StorageMaintenance Service Schedule Maintenance Before Each Work PeriodAfter Each Work Period HRSProblem Cause Error Code Machine TroubleshootingSolution Problem Cause Error Solution Machine Troubleshooting Controller Fault Codes Error Problem Solution Code

10052460, SG28, SG32, 10052450, 10052470 specifications

Windsor SG32, 10052470, 10052450, 10052460, and SG36 represent a line of cutting-edge products that have gained recognition for their innovative design and advanced technology. These models are characterized by their user-centric features tailored to enhance efficiency and comfort across various applications.

The Windsor SG32 stands out with its robust build and high-performance capabilities. Featuring a powerful motor, the SG32 is tailored for heavy-duty tasks, ensuring that it can handle extensive cleaning jobs with ease. Its ergonomic design allows for extended use without discomfort, making it a favorite among users who prioritize convenience and efficiency. The integrated dirt sensor technology is a notable feature that optimally adjusts the cleaning power based on surface conditions, guaranteeing thorough cleaning results every time.

Models 10052470, 10052450, and 10052460 share a commonality in their advanced filtration systems. These systems are designed to capture airborne particles effectively, making these models ideal for environments requiring enhanced air quality, such as hospitals and schools. The easy-to-replace filter cartridges reduce maintenance time, allowing users to focus on more critical tasks. Additionally, these models incorporate energy-efficient motors that minimize power consumption while maximizing performance, demonstrating Windsor's commitment to sustainability.

SG36, on the other hand, introduces smart technology with its intuitive touch control panel, allowing users to set operational parameters quickly. This model also features a quiet mode that is perfect for cleaning in noise-sensitive areas without sacrificing performance. The compact design of SG36 enhances maneuverability, making it suitable for tight spaces often found in urban settings.

All these Windsor models are equipped with high-capacity batteries for cordless operation, providing the freedom to clean without being tethered to a power outlet. This feature, coupled with LED indicators that signal battery life, ensures that users can operate with confidence. Maintenance is simplified due to the easily accessible components, meaning downtime for repairs is minimized.

In summary, Windsor SG32, 10052470, 10052450, 10052460, and SG36 boast a range of features aimed at enhancing cleaning efficiency while prioritizing user comfort and sustainability. Each model integrates advanced technologies that cater to various cleaning needs, solidifying Windsor's position as a leader in innovative cleaning solutions.
Top Page Image Contents