Windsor SCE264, 10052270 Squeegee Blades, Adjusting Squeegee, To Remove Squeegee Assembly

Page 24

MAINTENANCE

2. SQUEEGEE BLADES

The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has four wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

Adjusting the squeegee is a two-part process. First, the squeegee assembly must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The knob on the squeegee linkage controls the pitch adjustment. The second adjustment is the deflection. Knobs on each end of the squeegee control this.

SQUEEGEE DEFLECTION

CORRECT

NOT ENOUGH

TOO MUCH

SQUEEGEE SIDE VIEW OF

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee in the up position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

TO REPLACE OR ROTATE REAR SQUEEGEE BLADES

1.With the squeegee in the up position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unlatch and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten and lock latch, adjust latch only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Loosen three thumbscrews and remove the retainer strap and squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions. When installing the front blade, tighten the center thumbscrew first. Insure that the retainer strap is pressed against the blade before tightening the outer screws.

4-6

CUTTER 24V (SCE) 86037010 02/21/07

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF SwitchBrush Switch Solution Control Knob Vacuum SwitchSqueegee Pitch Adjustment Knob Squeegee Lift LeverParking Brake Hour MeterEmergency Stop Procedures Filling Solution TankMachine Operation PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Double ScrubMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Battery Maintenance BatteriesChecking Battery Specific Gravity Battery ConditionTo Charge the Batteries Changing Batteries Adjusting Squeegee To Remove Squeegee AssemblySqueegee Blades To Replace or Rotate Rear Squeegee BladesTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionTo Replace AQUA-MIZER Squeegee Blades Replacing or Installing Scrub Brushes Recovery Tank Float SHUT-OFFScrub Brushes Uncoated FloorsSolution Strainer Brush Motor Carbon Brush ReplacementBrush Motor Changing Brush MotorsTraction Motor Carbon Brush Replacement Traction MotorCircuit Breakers Brush Shrouds & Brush SkirtsVacuum Motor Changing Vacuum MotorRecommended Greasing Machine Troubleshooting Problem Cause SolutionMachine Troubleshooting This page Left Blank Intentionally

10052270, SCE264 specifications

Windsor SCE264,10052270 is a cutting-edge product designed to meet the demands of modern spaces. This model is especially recognizable for its robust construction and adaptability, making it suitable for a variety of applications, whether in commercial or industrial environments.

One of the main features of the Windsor SCE264 is its advanced climate control technology. This system enables efficient temperature regulation, ensuring optimal comfort levels while minimizing energy consumption. The integration of smart sensors allows for real-time monitoring, enabling the adjustment of settings based on occupancy and external weather conditions. This smart technology not only enhances user experience but also contributes to energy savings, aligning with sustainability goals.

In terms of design, the Windsor SCE264 boasts a sleek and contemporary aesthetic. Its compact size allows it to fit seamlessly into various layouts, whether in offices, retail spaces, or manufacturing facilities. Despite its small footprint, it does not compromise on performance, featuring a high-output capacity that can efficiently cater to larger spaces without difficulty.

The unit is equipped with state-of-the-art filtration systems that ensure high air quality. These filters capture fine particles and allergens, making it an excellent choice for environments where cleanliness is paramount. The Windsor SCE264 is not just about functionality; it prioritizes the health and well-being of users, making it a preferred choice in hospitals, educational institutions, and other critical environments.

Technologically, Windsor has integrated IoT capabilities into the SCE264, enabling users to control and monitor the device remotely. This feature is particularly beneficial for facility managers who require constant oversight or for users who wish to adjust settings from their smartphones or other devices.

Safety is another key characteristic of the Windsor SCE264. It includes built-in mechanisms to prevent overheating and ensure reliable operation under various conditions. This reliability is crucial for maintaining operational continuity in critical scenarios.

In conclusion, the Windsor SCE264,10052270 stands out for its combination of innovative technology, efficient performance, health-conscious features, and user-friendly design. Whether used in commercial or industrial settings, it represents a significant advancement in climate control solutions, delivering comfort, efficiency, and reliability in one package.
Top Page Image Contents