Machine Operation, General Information

GENERAL INFORMATION

As the carpet is being cleaned, check to see if there is foam building up in the recovery bucket. Add a little defoaming compound to the recovery tank but never to the solution tank.

For infrequent use or long periods of storage, flush the system with a neutralizing solution of 1 quart white vinegar mixed with 2 gallons hot water. Flush the system with clean hot water after neutralizing.

For hose fitting lubrication, use a light silicone lubricant which will not damage o-rings.

PROTECT THIS MACHINE FROM FREEZING.

PRE-RUN INSPECTION

1.Check all fittings and connectors for proper assembly.

2.Check all hoses for leaks. Repair or replace any damaged hoses.

3.Check power cord(s) for any damage. If damaged, replace.

EQUIPMENT SET-UP

1.Plug power cord from machine into properly grounded wall outlet.

2.Turn vacuum motor switch on and off to make sure there is electrical power at machine.

3.Connect vac hose to machine. Slide the swivel cuff over the outlet on the tank.

4.Connect the hose to your machine and wand. Pull back the knurled collar on the quick disconnect coupler (located on the solution tank) and push into the connection.

To avoid leaks, check to be sure that a positive connection was made.

5.Using a clean container, fill the solution tank with clean hot water. Mix in a non-foaming cleaning concentrate for use in hot water extraction machines, following the manufacture’s instructions printed on container.

MACHINE OPERATION

NOTE: When using a powder cleaner, pre-mix with hot water in a clean container before adding to the solution tank.

6.Turn pump and vacuum switch(s) to the on position.

7.Start cleaning.

EMPTYING AND CLEANING

Always use defoamer if foaming occurs. Foam will suspend

large particles that may damage vacuum(s) as well as allow liquid into the vacuum motor(s) without activating the float shutoff.

1.Before proceeding, make certain that the nozzle is functioning properly.

a.To check, hold the wand about one foot above the surface to be cleaned and open the wand valve. A full spray should be observed from the nozzle.

b.If the nozzle is not showing a full spray pattern, adjust nozzle for proper pattern, clean, or replace nozzle.

2.Normally, chemical is applied on the push stroke of the wand when cleaning. Vacuuming is done on the pull stroke. For heavily soiled carpets the wand may be used in a scrubbing manner, applying chemical in both the push and pull stroke.

3.When cleaning, keep the working opening (wand mouth) flat on the surface being cleaned. Keep the wand moving when the valve is open.

4.The shutoff float inside the vacuum tank will impede the vacuum flow when the vacuum tank is full. When this occurs, empty the vacuum tank by opening the dump valve and dispose of the waste in a proper manner.

5.Once the vacuum tank has been emptied, you may once again proceed with cleaning

ENSIGN 86038250 02/12/07

3-3

E50 10070090 specifications

The Windsor E50 10070090 is a cutting-edge device designed to meet the demands of modern commercial environments. Known for its robust construction and versatile functionality, this model stands out as a reliable solution for businesses seeking efficiency and durability.

One of the main features of the Windsor E50 is its powerful cleaning capability. Equipped with a high-performing motor, the E50 provides consistent suction and superior cleaning results. This makes it ideal for a wide range of surfaces, from carpets to hard floors, ensuring that every nook and cranny is attended to. The machine's advanced brush system further enhances its cleaning performance, enabling it to tackle tough dirt and grime with ease.

In addition to its cleaning prowess, the Windsor E50 10070090 incorporates innovative technologies that enhance user experience and operational efficiency. Its ergonomic design allows for easy maneuverability, which is essential in large commercial spaces. The intuitive controls ensure that operators can adjust settings quickly, adapting to different cleaning scenarios without any hassle.

The Windsor E50 is also designed with maintenance in mind. Its easy-access components simplify the maintenance process, reducing downtime and prolonging the machine's lifespan. The robust construction materials used in the E50 contribute to its durability, ensuring that it withstands the rigors of daily use in demanding environments like hotels, hospitals, and schools.

Another standout characteristic of the E50 is its remarkable energy efficiency. With rising energy costs and a growing emphasis on sustainability, the Windsor E50 has been engineered to consume less power while delivering exceptional cleaning results. This aligns with many businesses' goals to reduce their carbon footprint and operational expenses.

Moreover, the Windsor E50 10070090 features a compact design that makes storage and transportation effortless. Its lightweight nature allows for easy handling, making it a practical choice for various cleaning professionals.

In summary, the Windsor E50 10070090 is a powerful, efficient, and user-friendly cleaning machine. Its top-notch cleaning performance, innovative technologies, ease of maintenance, energy efficiency, and compact design make it an excellent investment for any commercial cleaning operation. As businesses seek reliable solutions to maintain cleanliness standards, the Windsor E50 stands as a trusted option that meets and exceeds expectations.