Windsor SPD-J manual Periodic Maintenance

Page 9

Periodic Maintenance:

These procedures are performed by a trained service technician. The regularity of these procedures may depend on the ma- chine's use.

1.) Flush the system with a special solution to reduce scaling (alkaline build-up).

Use acetic acid (white vinegar) or an anti-browning solution. Mix one quart acetic acid with 2 gallons (I:8 liters) of hot water in the solution tank (if an anti-browning solution is used follow manufacturer’s instructions). Turn on the vac/pump switch and allow the machine to run over a floor drain until the solution tank is empty (approximately once a month).

2.) Inspect hoses and cords, replace as needed.

3.) Inspect filter screens, clean or replace as needed.

4.) Inspect spray pattern of jets, replace or clean as needed.

5.) Check the tension of the solution valve cable, tighten if necessary.

6.) Inspect the vac motor, remove any lint build-up at cooling intake, service carbon vac motor brushes (Approximately every 750 operation hours).

7.) With the machine running, the brush should rotate freely without rattling or grinding. Replace bearings if necessary.

CAUTION:

Do not allow this machine to remain in a vehicle or area where the temperature will be below 40°F (4°C). Allowing this machine to freeze will cause damage not covered by the 6-3-1 warranty.

CAUTION:

Protect this machine from freezing if it becomes necessary to store it at temper- atures below 40°F (4°C).

Use a methyl hydrate window washer type anti-freeze; mix a gallon or two (4-8 liters) of anti-freeze solution, following the manufac- turer’s instructions. Add the anti-freeze solution to the solution tank. With the hoses in place run the machine until the anti-freeze begins spraying out (don't empty solution tank). Vacuum out the remaining anti- freeze solution in the solution tank. Discon- nect the hoses and empty the recovery buck- et. Always allow the unit to return to room temperature before filling with hot water or operating.

CAUTION:

Do not use Ethylene Glycol or any cooling system anti-freezes.

98353

Image 9
Contents Page Important Safety Instructions Advertissement Controls Preparing the Spirit Dual For Hard Floor Filling Solution TankSpirit Approved Accessory Tools To Use an Accessory ToolPlan Cleaning Route General Cleaning InformationDailv Maintenance Suggested Service Parts ListPeriodic Maintenance Troubleshooting Chart Troubleshooting Chart Servicing the Vac Motor Wire TerminalReverse Vac Shoe AssemblyRecovery & Solution Tanks Recovery & Tank Assembly Parts List Spray Jets Pump...Manifold...VaIveOpen HANDLE...CHASSIS...SWITCHES HANDLE,..CHASSIS...SWITCHES Parts List Brush Drive Assembly Brush Drive Assembly Parts List Vac Motor Assemblv Roller Vac Motor Roller Assembly Spirit Dual Squeegee Assembly 115V SPR Wiring Diagram Limited Warranty

SPD-J, SPD specifications

Windsor SPD and SPD-J are advanced power distribution systems designed with a focus on efficiency, reliability, and innovation. Windsor SPD, also known as Surge Protective Device, is engineered to protect electrical systems from voltage spikes that can result from lightning strikes, power surges, or other disturbances. This device is crucial for safeguarding sensitive electronic equipment used in various industries, from telecommunications to healthcare.

One of the main features of the Windsor SPD is its multi-level protection mechanism. It employs a tiered approach that combines several surge protection technologies, including metal oxide varistors (MOVs), gas discharge tubes (GDTs), and transient voltage suppressors (TVS). This combination not only enhances performance but also extends the lifespan of the protective equipment, effectively minimizing the risk of failure during transient events.

The SPD-J model introduces added functionalities and improved integration capabilities. It includes an intuitive monitoring interface that provides real-time insights into system performance and surge events. This data is crucial for facility managers as it enables them to assess the effectiveness of surge protection and make informed decisions about maintenance and upgrades.

Both the Windsor SPD and SPD-J feature compact designs that allow for easy installation in various settings, including residential, commercial, and industrial environments. Their robust construction ensures compliance with international safety standards, providing users with peace of mind regarding their efficacy.

In terms of technology, these devices are equipped with remote monitoring capabilities. Users can access performance data via web applications, enabling proactive management of electrical systems. Additionally, they are designed to integrate seamlessly with existing electrical infrastructure, making them a versatile solution for enhancing overall system resilience.

Regarding characteristics, the devices boast high energy absorption ratings, which define their ability to withstand and dissipate surges without compromising performance. The SPD and SPD-J are also designed to operate in a wide range of temperatures, ensuring reliability in diverse climate conditions.

In summary, Windsor SPD and SPD-J stand out in the field of surge protection technologies for their effective, user-friendly, and reliable solutions. As power demands continue to grow, these systems play an essential role in maintaining the integrity and safety of electrical systems across various sectors.