Wayne-Dalton 6600 installation instructions Cleaning Your Garage Door, Painting Your Garage Door

Page 19

Maintenance

Cleaning Your Garage Door

IMPORTANT: Do not use a pressure washer on your garage door!

While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct exposure to sunlight.

Cleaning the door will generally restore the appearance of the finish. To maintain an aestheti- cally pleasing finish of the garage door, a periodic washing of the garage door is recom- mended.

The following cleaning solution is recommended:

A mild detergent solution consisting of one cup detergent (with less than 0.5% phosphate) dissolved into five gallons of warm water will aid in the removal of most dirt.

NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for use in general cleaning of garage doors.

NOTE: Be sure to clean behind weatherstrips on both sides and top of door. Caution: Never mix cleansers or detergents with bleach.

Glass cleaning instructions

Clean with a mild detergent solution (same as above) and a soft cloth. After cleaning, rinse thoroughly.

Acrylic cleaning instructions

Clean acrylic glazing with nonabrasive soap or detergent and plenty of water. Use your bare hands to feel and dislodge any caked on particles. A soft, grit-free cloth, sponge or chamois may be used to wipe the surface. Do not use hard or rough cloths that will scratch the acrylic glazing. Dry glazing with a clean damp chamois.

NOTE: Do not use any window cleaning fluids, scouring compounds, gritty cloths or solvent- based cleaners of any kind.

Painting Your Garage Door

Surface preparation for painting

Wax on the surface must be removed or paint peeling/ flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a fine steel wool pad saturated with soapy water. A final wipe and rinse should be done with clean water only to remove any loose particles and any soapy film residue.

Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or no. 400 sand paper to create a smoother surface. Care must be taken to not expose the substrate under the paint. Once the substrate is exposed, the likelihood for rusting is greatly increased.

If substrate is exposed, it must be treated to prevent rust from forming. Sand the exposed area lightly and paint with a high quality metal primer specifically intended for galvanized surfaces to protect the area from corrosion. Allow for drying time on primer can label before applying topcoat.

The surface of the factory-applied finish, that is being painted, must not be too smooth, or the paint will not adhere to it. It is advisable to test in an inconspicuous area, to evaluate adhesion. If poor adhesion is observed, surface preparation for painting the factory-applied finish must be repeated until desired results are achieved. Again, care must be taken to not expose the substrate under the paint.

Caulking:

NOTE: After surface has been properly prepared use acrylic latex plus silicone caulk. Fol- low caulking label directions explicitly. It must be allowed to dry thoroughly prior to painting.

1.Caulk the top edge of all horizontal stiles to the section (Top, Intermediate(s), Lock and Bottom sections) surface.

Caution: Do not caulk bottom edge of any horizontal stiles.

Caution: Do not caulk vertical or diagonal stiles. 2. Caulk exterior overlay to glass in all lite cutouts for lited sections.

Painting:

NOTE: When painting the section, the paint must not seal the bottom edge of any stiles to the section surface.

After surface has been properly prepared, it must be allowed to dry thoroughly, and then coated immediately with premium quality latex house paint. Follow paint label directions explicitly. Oil base or solvent base paints are not recommended. Please note that if substrate is exposed and not properly primed, painting with latex paint may cause accelerated rusting of the steel in the exposed area.

NOTES:

1.Re-painting of finish painted steel doors cannot be warranted, as this condition is totally beyond the door manufacturer’s control.

2.Consult a professional coatings contractor if in doubt about any of the above directions.

3.Follow directions explicitly on the paint container labels for proper applications of coatings and disposal of containers. Pay particular attention to acceptable weather and temperature conditions in which to paint.

Wood (Preparation and Painting)

These instructions apply to all Wood Doors produced and sold by Wayne-Dalton. The exterior surfaces, as well as all edges must be properly painted and maintained if satisfactory performance is to be achieved. The purpose for painting is to both protect and beautify

the substrates. These requirements for finishing are intended to achieve both functions for reasonable service life of wood doors. Wood doors must be completely finished prior to installation, to ensure that the interior and exterior surfaces, as well as all edges of the doors

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Li g h t Co m m e rci al B l e O f C o n t e n t sImportant Notices Part NumberPackage Contents Important Safety InstructionsTools Required Bottom section Removing an Existing DoorDoor Section Identification Preparing the OpeningHeadroom Requirements Track Rollers Page Graduated Hinge / Strut Attachment Bottom Corner bracketsPull Handles Inside Lift HandlesBottom Section Lift HandlesVertical Tracks If you have Top Fixture Bases and Top Fixture Slides If you have Top Fixture AssembliesOperator Bracket Top SectionHorizontal Tracks Center Bracket End Bearing BracketsIf you don’t have a Coupler Assembly Torsion Spring AssemblyIf you have a Coupler Assembly Torsion Spring Attachment Coupler assemblyCounterbalance Lift Cables Set screws Torsion shaft Torsion keyed shafts Winding SpringsJamb Locking pliersClamps, Tape measure, Level, Hammer, Step Ladder Perforated Angle Gauge Weight Limitations Door WeightRear Back Hangs TagsVice clamp 2nd Track roller Sound framing Members To 7/8 Horizontal tracks16 Bolts and nuts Perforated angle Pull Down Rope Important Not caulking your door may void the warrantyDoor Arm Hookup Inside LockSurface preparation for painting Cleaning Your Garage DoorPainting Your Garage Door Important Do not use a pressure washer on your garage doorOperating Your Garage Door Manual door operation Operation And MaintenanceWood Maintenance and Refinishing Using an electric operatorLimited Lifetime warranty Model Warranty

6600 specifications

The Wayne-Dalton 6600 is a versatile and robust fiberglass garage door designed to meet the needs of residential homeowners who prioritize both aesthetics and durability. This innovative door stands out for its unique blend of features, technologies, and characteristics that cater to various styles and preferences.

One of the standout features of the Wayne-Dalton 6600 is its superior insulation properties. The door is constructed with a high R-value, ensuring excellent thermal efficiency. This is particularly beneficial in regions with extreme temperatures, as it helps maintain a comfortable garage environment while potentially lowering energy costs for heating and cooling.

The Wayne-Dalton 6600 also boasts a lightweight design, making it easier to operate without compromising strength and durability. Unlike traditional steel doors, the fiberglass construction is resistant to rust and corrosion, ensuring longevity even in harsh weather conditions. Homeowners can enjoy peace of mind knowing that their investment is protected against the elements.

Aesthetically, the garage door is available in a variety of colors and finishes, allowing homeowners to customize their door to complement the overall design of their home. The realistic wood grain textures available add a touch of elegance and warmth, providing the classic look of wood without the maintenance associated with natural materials.

In terms of technology, the Wayne-Dalton 6600 incorporates a unique, high-quality pully and track system that ensures smooth operation. This system is designed to minimize wear and tear over time, enhancing the door's lifespan and performance. Additionally, the door is compatible with a range of smart home technologies, giving homeowners the convenience of remote access and control, enhancing security and ease of use.

Safety is a top priority for Wayne-Dalton, and the 6600 reflects this commitment with features such as pinch-resistant edges and an automatic reversal system that prevents accidents and injuries. The door is built to provide peace of mind for families, ensuring that the garage remains a safe space for both people and pets.

In conclusion, the Wayne-Dalton 6600 is an exemplary product for homeowners seeking a blend of functionality, style, and safety. With its innovative materials, customizability, and advanced technology, it offers a reliable and attractive solution for any home’s garage door needs. Homeowners who invest in the Wayne-Dalton 6600 can expect unmatched performance and enduring beauty for years to come.
Top Page Image Contents