sticker, with the lower alignment sticker on right hand side, on the back of door. Keep sec- tions aligned and fasten center hinge(s) first; then end hinges last using
NOTE: To prevent center hinge leaf(s) from rotating, first secure the top middle hole of the center hinge leaf with one 1/4” – 14 x 5/8”
NOTE: Larger doors with double graduated end hinges, fasten both hinges to connect the sections using 1/4” - 14 x 5/8”
Repeat same process for other sections, except top section.
Important: Push & hold the hinge leafs securely against the sections while securing with
allowing the drawbar operator bracket to slide between the section and the strut.
NOTE: For retro fit applications, the drawbar operator bracket must be aligned with an exist- ing drawbar operator.
Locate the center of the top section and slide drawbar operator bracket under strut till the drawbar operator bracket is seated against the strut flange.
NOTE: Prior to fastening drawbar operator bracket to top section, ensure the top edge of drawbar operator bracket is aligned with the top edge of the section, as shown.
Attach the drawbar operator bracket using (6) 1/4” – 20 x 5/8” self drilling screws (as shown). Finish
|
|
| Alignment | |||
Lock section | ||||||
sticker | ||||||
|
|
|
|
|
| |
|
|
|
|
|
|
Left double graduated |
| Vertical | |||||||
end hinge with long |
| ||||||||
| stem track roller |
| tracks |
|
|
| |||
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Top section
Strut
1/4” - 20 x 7/8”
Top section
Drawbar operator bracket
Strut
Right double graduated
end hinge with long
stem track roller
Alignment sticker
1/4”-14 x 5/8” Self tapping screw locations
Secure top
middle hole first
Left graduated end hinge | Center | Right graduated end hinge | |
hinge(s) | |||
with short stem track roller | with short stem track roller |
Drawbar operator | (6) 1/4” - 20 x 5/8” |
bracket in place | |
under strut |
|
11 | Top Section |
Tools: Hammer, Power drill, 7/16” Socket driver, 7/16” Socket, 7/16” |
Place the top section in the opening. Temporarily secure the top section by driving a nail into
9 | Top Fixtures |
Tools: Power drill, 7/16” Socket driver |
NOTE: The top fixtures come
Starting on the left hand side, locate the edge of the top section and seat the top fixture on male part of the top section, as shown.
1.Attach one 1/4” - 20 x 11/16”
2.Attach two 1/4” - 20 x 11/16”
3.Attach two #12 x 1/2” phillips head screws on the opposite side of top fixture assembly. Insert short stem track roller into top fixture slide. Repeat for left hand side.
| Short stem track roller | 3. (2) 12# x 1/2” | |
|
|
| |
|
|
| Phillips head screws |
Top fixture slide |
|
|
|
Top fixture |
|
| Top section |
|
|
| |
assembly |
|
|
|
2. (2) 1/4”- 20 x 11/16” | 1. (1) 1/4”- 20 x 11/16” | ||
| |||
|
| ||
|
|
|
10 | Drawbar Operator Bracket |
Tools: Power drill, 7/16” Socket driver |
Note: If you’re installing a drawbar operator, the drawbar operator bracket must be mounted and secured prior to installing top section.
Important: when connecting a drawbar operator type garage door opener to this door, a
Remove, but retain
the header near the center of the door and bending it over the top section. Now, flip up the graduated end hinge and center hinge leaves, hold tight against section, and fasten center hinges first and end hinges last (refer to step, Stacking Sections). Vertical track alignment is critical. Position flag angle between
Important: the dimension between the flag angles must be door width plus
For Quick Install Track:
Complete the vertical track installation by securing the jamb bracket(s) and tightening the other lag screws. Repeat for other side.
For Fully Adjustable track:
Complete the vertical track installation by securing the jamb bracket(s) and tightening the other lag screws. Push the vertical track against the track rollers so that the track rollers are touching the deepest part of the curved side of the track; tighten all the track bolts and nuts. Repeat for other side.
Door width |
+ |
Flag angle |
Nail |
Top section |
to |
Flag |
angle |
Top |
section |
Vertical track |
against track rollers |
8
Please Do Not Return This Product To The Store. Contact your local
refer to your local yellow pages business listings or go to the Find a Dealer section online at