LED and Horn Patterns, ING the CO Alarm

LED AND HORN PATTERNS

LIGHTS

GREEN light ON

YELLOW light blinks once per minute

YELLOW light blinks during horn ramp-up.

RED blinks 4 times right after horn sounds.

YELLOW light blinks during horn ramp-up.

RED blinks 4 times right after horn sounds.

YELLOW light flashes 2 times per minute after horn beeps

YELLOW light flashes 3 times per minute after horn beeps

YELLOW light flashes constantly after horn beeps

RED light flashes 4 times right after horn

RED light flashes 3 times every 10 seconds

RED light flashes 1 time every 10 seconds

SMART BUTTON KEY

Quick push activates a local Push-to-Test sequence

Press and RELEASE button before you hear the third chirp. The system will perform a single local test cycle.

Press and HOLD button.

The system will perform a single local test cycle, then repeat the interconnect test until you release the button.

Quick press will eliminate the low-battery warning for about 10 hours

Smart Button WILL NOT silence the low battery chirp! Replace battery immediately!

Press to check the alarm again. Replace alarm if it remains in the fault condition.

Quick press activates CO Reset

Quick press erases the CO latched signal

Quick press activates Smart Quiet™ Trigger Alarm locator for Model COE and COEA alarms.

ING THE CO ALARM

WARNING DO NOT disconnect the battery or AC power to quiet an unwanted alarm. This will remove your protection.

Use Quick Quiet™ False Alarm Control by pushing the Smart Button.

PROBLEM	SOLUTION

The horn beeps once,	The alarm is operating properly. The Firex patented
then two beeps, then	Horn Ramp-Up feature lets you start the test sequence
three beeps, pauses, and	and move away from the unit before the full alarm
then sounds the full	horn sounds.
alarm when using the
Smart Button to test.

Alarm sounds;	Take Emergency Safety Actions in all alarm situations! If
no hazard present.	no hazard proves to be present: Test the alarm to check
	for proper functioning. Clean the alarm. (See TESTING
	AND MAINTENANCE.) Check that the alarm is placed
	properly. (See AGENCY RECOMMENDATIONS FOR
	ALARM PLACEMENT.)

The alarm beeps once a	The battery needs to be replaced. Turn off power and
minute and YELLOW	replace the battery. (See “REPLACING THE BATTERY” in
light flashes.	“TESTING AND MAINTENANCE”.) Push the Smart Button
	to temporarily quiet the low battery signal for 10 hours.

Horn beeps twice a	Push the Smart Button to allow alarm to reset and self
minute and YELLOW	test. If fault signal continues, alarm is no longer providing
light flashes.	protection and must be replaced.

For Technical Support:

PH: (800) 445-8299

Email: technical service@invensys.com

Website: www.icca.invensys.com/firex

SERIES 10000 specifications

The Firex SERIES 10000 represents a cutting-edge advancement in fire safety technology, designed to enhance both efficiency and reliability in protecting residential and commercial environments from fire hazards. This innovative series is equipped with a range of features that set it apart in the realm of fire detection and alarm systems.

One of the standout characteristics of the Firex SERIES 10000 is its advanced sensing technology. The system utilizes a dual-sensor mechanism that combines both photoelectric and ionization detection. This hybrid approach ensures comprehensive coverage by being able to detect smoldering and fast-flaming fires, significantly reducing the risk of false alarms while maintaining a rapid response time.

The Firex SERIES 10000 is engineered with smart connectivity features, allowing it to integrate seamlessly with existing home automation systems. Through Wi-Fi connectivity, users can monitor their fire alarm systems remotely via a smartphone application. This feature not only provides real-time notifications about potential threats but also allows users to check the status of their alarms from anywhere, offering peace of mind even when away from home.

Energy efficiency is another key attribute, with the SERIES 10000 designed to consume minimal power while maintaining peak performance. The system employs a low-energy standby mode, ensuring that battery life is prolonged without sacrificing reliability. This design consideration translates to reduced operational costs and environmental benefits.

Moreover, the Firex SERIES 10000 is built with durability in mind, featuring a weather-resistant enclosure suitable for installation even in challenging environments. This durability ensures long-lasting performance, making it an ideal choice for various applications, from residential settings to commercial buildings and industrial facilities.

The user-friendly interface is enhanced with intuitive controls, allowing for easy installation and maintenance. Clear visual indicators and audible alerts facilitate straightforward operation, ensuring that users can quickly understand the system’s status and respond appropriately in case of an emergency.

In summary, the Firex SERIES 10000 is a top-tier fire detection system that combines advanced technology, smart connectivity, energy efficiency, and user-centric design. Its robust features cater to the evolving needs of modern fire safety, making it an indispensable tool in safeguarding lives and properties from fire emergencies.