Maintenance, Peak Level Memory Reset, Testing

7.Model KN-COP-IC (with digital display) Operating Characteristics

The following table illustrates the possible digital displays, describes the audible alarm patterns, and the recommended actions to take.

Operating and Alarm Characteristics

LED Display Shows	Alarm Sound	Unit Status	Recommendation

Brief “888” along	4 quick beeps,	Self checking when	None – CO has not
with any number	5 seconds	AC powered (Test	been detected.
between 100 and 300.	silence,	button was pressed	Numbers shown for
Red LED flashes with beeps.	repeated once	or unit was first	test purposes only
Green and amber LED’s on.		powered)

Steady “0”	None	Normal AC	None
Green LED		operation (sensing
constantly on.		no CO) and with a
		good battery

“Lb” flashes	One quick	AC powered and	Install or replace 9V
alternately with	beep every	low or missing	battery.
any number.	15 seconds	battery
Red LED flashes
every 15 seconds.

A steady display of	4 quick beeps,	Alarm condition.	Refer to “What to do
CO concentration	5 seconds	Dangerous	When the Alarm
from 30-999. Red	silence,	concentrations of	Sounds” (inside front
LED flashes with beeps. Amber	repeating	CO detected	cover)
LED shows initiating alarm.

Steady “CO”	4 quick beeps,	Interconnected CO	Refer to “What to do
Red LED flashes with	5 seconds	alarm warning of a	When the Alarm
beeps. Amber LED	silence,	CO condition	Sounds” (inside front
shows initiating alarm	repeating		cover)

“FirE”	3 long beeps,	Interconnected	Evacuate by your
Red LED flashes	1 second	smoke alarm	escape plan
with beeps	silence,	warning of a
	repeating	smoke/fire condition

Steady “Err”	One quick	Unit malfunction	Replace battery.
Red LED flashes every	beep every		If “Err” continues,
30 seconds	30 seconds		unit has malfunc-
			tioned. Replace
			immediately. Unit will
			not respond CO

No display alternating	4 quick beeps,	Alarm condition	Refer to “What to do
with display of CO	5 seconds	powered on battery	When the Alarm
concentration every 60	silence,	backup. Dangerous	Sounds” (inside front
seconds. Red LED	repeating	concentrations of	cover).
flashes with beeps	every 60 secs	CO detected	Replace battery

No display alternating	None	Normal operation	Verify AC power is
with “0” every 60		after first 4 minutes	restored as soon as
seconds.		of 9 V battery	possible to conserve
Green LED flashes		operation. Unit	battery.
every 7 seconds		monitoring for CO	Replace battery

7.Model KN-COP-IC (with digital display) Operating Characteristics

Peak Level Memory (model KN-COP-IC only)

When the Peak Level button is pressed and held, the display shows the highest CO reading taken by the CO alarm since its last reset or power up. The Peak Level display feature will display levels between 11-999 PPM. Although the Peak Level feature will display levels below 30 PPM, these levels will not result in an alarm no matter how long the device is exposed to these levels. The Peak Level feature is helpful in identifying if you have had a CO reading since resetting the alarm.

Concentrations of CO between 1 and 30 PPM can often occur in nor- mal, everyday conditions. Concentrations of CO below 30 PPM may be an indication of a transient condition that may appear today and never reappear. Some CO conditions may start out as low level leaks but could develop into CO concentrations that may become harmful.

Peak Level Memory Reset

Press the Peak Level button; with the button still pressed, press the Test/Reset button for two seconds and release. The number on the dis- play will turn to “0”, the memory will be cleared and the alarm will begin monitoring for CO. The Peak Level memory is also reset when the unit loses power.

8. Maintenance

NOTE: This unit is sealed. The cover is not removable.

Due to the loudness of the alarm, we suggest that you place your fingers over the sounder opening while testing your alarm.

CAUTION: Continuous exposure to the high sound level of this alarm over an extended period of time may cause hearing loss.

Testing

To test the alarm, press the Test/Reset button. If the unit is operating properly, you should hear 4 quick beeps – followed by 5 seconds of silence – followed by 4 quick beeps. (For model KN-COP-IC with digi- tal display: The display will show three “eights” and then show a num- ber – usually around 200). The red LED will flash along with the beeps and the amber LED will illuminate. Within several seconds the unit will return to monitor for CO.

If interconnected to Kidde smoke alarms, pressing the Test/Reset button on the CO alarm will have no effect on the smoke alarms. The smoke

kn-cop-ic, kn-cobic specifications

The Kidde KN-COP-IC and KN-COB-IC are advanced carbon monoxide (CO) and explosive gas detectors designed to enhance home safety through state-of-the-art technology. These devices serve as a crucial line of defense against the dangers posed by carbon monoxide, a colorless, odorless gas that can lead to serious health risks or even fatality if undetected.

One of the main features of the Kidde KN-COP-IC is its electrochemical CO sensor, which provides accurate readings while also minimizing the chances of false alarms. This sensor technology allows the device to detect the presence of carbon monoxide at lower concentrations, making it effective in a variety of environments, including homes, garages, and other enclosed spaces. The KN-COB-IC model, focusing on explosive gases, utilizes a sophisticated catalytic bead sensor that can precisely identify the presence of combustible gases, such as natural gas and propane.

Both models are equipped with a digital display that provides real-time readings, making it easy for users to monitor CO levels and other hazardous gases present in their environment. The KN-COP-IC offers a peak level memory feature, which stores the highest levels of CO detected since the last reset. This helps users understand previous exposure levels, potentially informing safety and health decisions.

In terms of installation and usability, the Kidde detectors come with a battery backup to ensure continuous operation, even during power outages. They are designed for easy mounting, whether on walls or ceilings, and are compact enough to blend seamlessly into home decor. Furthermore, the integrated test/silence button allows users to check the functionality of the alarm and silence it during false alarms or maintenance checks.

Both the KN-COP-IC and KN-COB-IC models meet stringent safety standards and certifications, ensuring they provide reliable protection. Regular maintenance is simplified with clear instructions included in the user manual, along with the recommendation to replace the units after a specified period, usually around 7 years for CO detectors.

In conclusion, the Kidde KN-COP-IC and KN-COB-IC are essential tools in modern home safety. With their advanced sensor technology, user-friendly features, and reliable performance, these detectors not only safeguard families from carbon monoxide and explosive gases but also promote peace of mind in everyday living. By investing in these reliable detectors, homeowners can ensure the safety and well-being of their loved ones.