About the controls on the dehumidifier, Power Pad

About the controls on the dehumidifier.

4 hour or 2 hour	High, Medium	Clean the Filter	Continuous operation on
delay off	and Low fan	indicator light		indicator light
indicator lights	indicator lights

Bucket Full light indicates bucket needs to be emptied or is not in place in the unit

Power On

indicator light

Controls

Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

NOTE: When the bucket is full or removed, the controls cannot be set.

Power Pad

Press to turn the dehumidifier on and off.

Filter Timer

After 250 hours of operation, the Clean the Filter indicator light will glow to remind you to clean the filter. Remove the filter and clean it.

Press to turn off the Clean the Filter light. See

the Care and Cleaning section.

Humidity Set Control Pads

The humidity level can be set within a range of 35% RH (Relative Humidity) to 80% RH (Relative Humidity) in 5% increments or at CO for continuous operation. To set the unit for continuous operation, press the ▼ pad until the screen reads CO.

NOTE: If CO (Continuous) is selected, the dehumidifier will operate continuously at its maximum dehumidification settings if attached to a hose to drain or until the bucket is full.

For drier air, press the ▼ pad and set to a lower percent value (%).

For damper air, press the ▲ pad and set to a higher percent value (%).

Other Features

When you first use the dehumidifier, set

the humidity control to 45% or 50%. Allow at least 24 hours for the dehumidifier to achieve the humidity level. If you still have damper air than desired, set the humidity level to a lower setting or select Continuous for maximum dehumidification.

Display

Shows the set % humidity level while setting, then shows the actual (+/– 5% accuracy) room % humidity level.

Fan Speed Pad

Controls the fan speed.

Press to select either High, Medium or Low fan speed.

Set the fan control to High for maximum moisture removal. When the humidity has been reduced and quiet operation is preferred, set the fan control to Medium or Low.

Delay Off

While the dehumidifier is in operation, press this pad to set it to automatically turn off in 2 hours or 4 hours.

Consumer Support

BUCKET FULL Light

Glows when the bucket is ready to be emptied, or when the bucket is removed or not replaced in the proper position.

Alarm

If the bucket is full or missing for more than 3 minutes, an alarm will sound for about 10 seconds to remind you to empty and replace the bucket.

4	Auto Shut Off
	The Water Level Control Switch shuts off the

dehumidifier when the bucket is full, or when

the bucket is removed or not replaced in the proper position. NOTE: Fan will continue to run approximately 3 minutes after bucket is removed.

Auto Defrost

When frost builds up on the evaporator coils, the compressor will cycle off and the fan will continue to run until the frost disappears.

Power Outage

In the case of a power outage or interruption, the unit will automatically restart, in the settings last used, after the power is restored.

ADEH50 specifications

The GE ADEH50 is a cutting-edge heat pump that has gained significant attention in the market for its advanced features and energy-efficient technology. As homeowners and businesses alike seek sustainable solutions for temperature regulation, the ADEH50 emerges as a strong contender, combining efficiency, reliability, and innovative design.

At the heart of the GE ADEH50’s performance is its highly efficient variable-speed compressor. This technology enables the heat pump to adjust its output according to the immediate heating or cooling demands of a space. By operating at different speeds, the ADEH50 can maintain a consistent indoor temperature with minimal energy consumption, significantly reducing electricity costs compared to traditional single-stage systems.

Another noteworthy characteristic of the GE ADEH50 is its use of environmentally friendly refrigerants. The heat pump employs R-410A refrigerant, which has been recognized for its low global warming potential. This commitment to eco-friendly technology not only aligns with environmental regulations but also meets the growing consumer demand for sustainable products.

The ADEH50 also features advanced smart technology integration. It can be connected to Wi-Fi, allowing users to control their heating and cooling systems remotely via smartphone apps. This feature not only enhances convenience but also enables homeowners to optimize energy usage by adjusting settings according to occupancy patterns, ultimately leading to increased savings and a reduced carbon footprint.

In terms of design, the GE ADEH50 is built to withstand various weather conditions. Its robust construction includes a durable cabinet and corrosion-resistant components, ensuring longevity and reduced maintenance needs. The heat pump is also equipped with a quiet operation technology that minimizes noise, making it an ideal choice for residential areas where peace and comfort are a priority.

The GE ADEH50’s capacity options cater to diverse needs, making it suitable for different sizes of spaces. Its energy efficiency is reflected in its high Seasonal Energy Efficiency Ratio (SEER) and Heating Seasonal Performance Factor (HSPF) ratings, which signify its effectiveness in both cooling and heating modes.

In summary, the GE ADEH50 stands out in the heat pump market, offering a blend of advanced technology, environmental sustainability, and reliable performance. With its variable-speed compressor, smart technology integration, and durable design, it is an excellent investment for anyone looking to enhance comfort while promoting energy efficiency and sustainability in their living or working environment.