KitchenAid 30" (76.2 cm) Slide-in ranges, Tools needed for installation, Product dimensions

Slide-in ranges:

countertop preparation

30"
(76.2 cm)
opening	1/2"
width
	(1.3 cm)

30-7/8"

(78.4 cm) Formed or tiled countertop trimmed 1/2" (1.3 cm) back at front corners of countertop opening.

25"

(63.5 cm)

Cooktop sides of range fit over edges of countertop opening.

Tools needed for installation:

Assemble the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

• level

• Phillips scewdriver

• flat-blade screwdriver or 5/16”"(7.9 mm) nut driver

• 3/8" ( 9.5 mm) ratchet

• adjustable wrench

• pliers

• hammer

The cooktop sides of the slide-in range fit over the cutout edge of your countertop.

If you have a square finish (flat) countertop and the opening width is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops: Must have molded edge shaved flat 1/2" (1.3 cm) from each front corner of opening.

Tile countertops may need trim cut back 1/2" (1.3 cm) from each front corner and/or rounded edge flattened.

Product dimensions

If countertop opening width is greater than

30" (76.2 cm), adjust the 1/2" (1.3 cm) dimension.

Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Oven must be level for satisfactory baking conditions.

• measureing tape or ruler

• hand or electric drill

wood floor: 1/8" (0.3 cm) drill bit

concrete/ceramic floor: 3/16" (0.48 cm) carbide-

tipped masonry drill bit

• L.P. gas conversion requires: pin pick up (claw

attachment)

• 5/16" nut driver

Parts supplied for installation:

• burner grates and caps

• vent cap

Freestanding Range

• L.P. conversion orifice spud kit:

8-1/4"
	30" (76.2 cm)
(21 cm)
	range width

36-1/8"

(91.8 cm)

cooktop

height

1 – 0.95 mm (0.0374") cooktop (blue)

2 – 0.67 mm (0.0264") cooktop (black)

1 – 1.05 mm (0.0413") cooktop (green)

1 – #65 (0.0350") broil burner

anti-tip bracket

44-3/8"

(112.7 cm)

2 screws (#10 x 1-1/2")

2 plastic anchors

1"

(2.54 cm) spacer

28"

(71.1 cm)

depth

with

handle

(Bracket must be securely mounted to sub-floor. Thickness of flooring may require longer screws to anchor the bracket to sub-floor.)

Mobile home installation

The installation of this range must conform to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280); or when such standard is not applicable, the Standard for

Slide-in Range

Manufactured Homes Installations (Manufactured Home Sites, Communities and Setups), ANSI A225.1/NFPA 501A*, or with local codes.

	30" (76.2 cm)
1-1/2"
	rear vent width
(3.8 cm)

1"

(2.54 cm) spacer

28"

(71.1 cm)

depth

with

handle

IMPORTANT: Rear vent must not be obstructed for proper ventilation on all slide-in models. See Step 7, Panel D.

36-1/8"

(91.8 cm)

cooktop

height

30"

(76.2 cm)

width

In Canada, the installation of this range must conform with the current standards CAN/CSA-Z240 — latest edition**, or with local codes.

When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Copies of the standards listed may be obtained from:

*National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

**CSA International

8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

Anti-tip bracket:

The floor anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see Panel D and the anti-tip bracket template.

Panel B