Beckett ADC manual Maintain & Service Burner, Owner’s Information Professional Service Required

Page 12

Section: Maintain & Service Burner

Maintain & Service

Burner

A. Owner’s Information

Professional Service

Required

Incorrect installation, adjustment, and use of this burner could result in severe personal injury, death, or substantial property damage from fire, carbon monoxide poisoning, soot or explosion.

Please read and understand the manual supplied with this equipment. This equipment must be installed, adjusted and put into operation only by a qualified individual or service agency that is:

yLicensed or certified to install and provide technical service to oil heating systems.

yExperienced with all applicable codes, standards and ordinances.

yResponsibleforthecorrectinstallationandcommission of this equipment.

ySkilled in the adjustment of oil burners using combustion test instruments.

The installation must strictly comply with all applicable codes, authorities having jurisdiction and the latest revision of the National Fire Protection Association Standard for the installation of Oil-burning Equipment, NFPA 31 (or CSA-B139 and CSA-B140 in Canada).

Regulation by these authorities take precedence over the general instructions provided in this installation manual.

Have your equipment inspected at regular intervals by a qualified service agency to assure continued proper operation. The burner should be adjusted using dedicated combustion test equipment. Failure to properly set the burner could result in inefficient operation, and/or conditions that could potentially cause severe personal injury, death or substantial property damage.

B. Owner Service and Maintenance

Properly installed and maintained, your ADC burner will provide years of efficient, trouble-free operation. Please take care of your equipment by following the warnings provided and by immediately contacting your qualified

service agency if your burner is not operating properly. This equipment should be serviced only by a qualified service agency. The appropriate test instruments must be used.

Daily

Check the area around your burner/equipment to make sure:

○Nothing is blocking the burner inlet air openings.

○Air ventilation openings are clean and unobstructed and the exhaust is not crusted.

○No combustible materials are stored near the equipment.

○There are no signs of oil or water leakage around the burner or equipment.

Extended Down Time

If the equipment will be stored for an extended period of time, insure that the fuel tank is full and add a fuel stabilizer to the tank.

Regular Service/Maintenance

Have your burner, serviced annually by your qualified service agency. The following components/assemblies should be checked/adjusted/replaced on a regular basis. Refer to the Replacement Parts exploded view for part locations.

□Replace the oil supply line filter, if applicable. The line filter cartridge must be replaced to avoid contamination of the pump and nozzle.

□Inspect the oil supply system. All fittings should be leak-tight. The supply lines should be free of water, sludge and other restrictions.

□Remove and clean the pump strainer.

□Verify the nozzle is the one originally specified by the appliance manufacturer and replace the nozzle with one having the exact specifications from the same manufacturer.

□Clean and inspect the electrodes for damage, replacing any that are cracked or chipped.

□Check electrode tip settings. Replace electrodes if tips are rounded.

□Inspect the igniter spring contacts. Clean or replace if corroded.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 12Vdc Oil Burner Manual Potential for Fire, Smoke and Asphyxiation HazardsContents Prepare Before Installing Specifications Owner’s ResponsibilityGeneral Information Nozzle Assembly Maintenance Low Firing Rate BaffleReplace the Burner Nozzle Check/Adjust Electrodes Igniter MaintenanceServicing Nozzle Line Assembly Check/Adjust Z DimensionBurner Wiring Fuel SupplySection Burner Wiring Drive Component Maintenance Motor, Blower Wheel, and Coupling ReplacementPump Maintenance Valve Coil and Stem ReplacementStart Up Burner & Set Combustion Basic Burner OperationCombustion Set-up Explosion and Fire HazardSet Combustion with Instruments Maintain & Service Burner Owner’s Information Professional Service RequiredOwner Service and Maintenance Regular Service/MaintenanceTroubleshooting 125 140 150 175 200Rated Psi PsigTroubleshooting Chart Replacement Parts 2320 1618Limited Warranty Information

ADC specifications

Beckett Advanced Digital Control (ADC) represents a significant advancement in the world of heating technology, offering homeowners enhanced efficiency, control, and convenience in managing their heating systems. This innovative technology is designed to integrate seamlessly with various heating solutions, including oil and gas furnaces, boilers, and water heaters.

One of the main features of Beckett ADC is its advanced control algorithms, which enable precise modulation of fuel delivery and combustion processes. This modulation not only optimizes energy consumption but also minimizes emissions, ensuring compliance with environmental standards. The ADC system intelligently adjusts the fuel flow based on the heating demands of the home, thus achieving a high degree of efficiency.

The user interface of the Beckett ADC is another standout characteristic. It features a digital display that provides real-time feedback on system performance, making it easy for homeowners to monitor their heating systems. The interface is designed to be user-friendly, allowing for quick adjustments and settings changes without technical expertise.

In terms of technology, Beckett ADC utilizes sophisticated sensors that monitor various parameters, including temperature, pressure, and airflow. This data is constantly analyzed to ensure optimal operation. The system also incorporates advanced ignition technology, which allows for a quick and reliable start, thus enhancing the overall user experience.

Another key characteristic of Beckett ADC is its compatibility with smart home systems. Many models are designed to connect with Wi-Fi and can be integrated into home automation platforms. This allows homeowners to control their heating systems remotely, enabling features such as scheduling, temperature adjustments, and real-time monitoring from a smartphone or tablet.

Additionally, Beckett ADC is known for its durability and low maintenance requirements. The design incorporates high-quality materials that resist wear and tear, allowing for a longer lifespan and reliable operation over time. This durability ensures that homeowners can enjoy an efficient heating system without the frequent need for repairs or replacements.

In summary, Beckett ADC stands out in the heating industry for its advanced digital control capabilities, user-friendly interface, sophisticated sensor technology, smart home compatibility, and durable design. These features come together to create an efficient, convenient, and environmentally friendly heating solution for modern homes, underscoring Beckett's commitment to innovation and quality in heating technology.
Top Page Image Contents