Startup / Checkout, Wiring, Starting the System

■Wiring:

CAUTION Incorrect Wiring Will

Result in Improper

Control Operation

yGeniSys 24V wiring label colors may not match the wire colors of the burner or other manufacturers’ controls.

yThe GeniSys 24V Control should be wired according to the equipment manufacturer’s instructions.

○Make sure all equipment wiring complies with all local codes and ordinances.

○Make connections to the control’s terminals as shown in Figure 2. Refer to the label on the underside of the control for wiring details.

○Motor-off delay on a 7559P will be disabled if the safety and operating limits as shown in Figure 2 interrupt power to the control’s red +24 volt wire.

○Input power to the control’s red +24 volt wire must be provided from a fused service switch, rated at 50 amps or less.

Startup / Checkout

If the burner or control fails any of the following tests, recheck control wiring. If the burner or control still fails any tests, replace the control.

■Starting the System

1.Open the shut-off valve(s), if applicable, in the supply line from the oil tank.

2.Close the disconnect switch to supply power to the burner.

3.Adjust the thermostat to call for heat.

▪If the pump has not been primed, refer to “Priming the Pump” in this manual.

4.Monitor burner operation to insure that the burner ignites.

5.End the call for heat. Verify that the burner turns off before leaving the installation site.

■Check Safety Features

○Safe Start Check

1.Place a jumper across the cad cell terminals.

2.Refer to the steps for

“Starting the System” and have the system call for heat.

3.Burner must not start. Verify that the control remains in Standby mode.

4.End the call for heat and remove the cad cell jumper.

○Simulate Flame Failure and Ignition Failure

1.Refer to the steps for “Starting the System” and have the system call for heat.

2.After ﬂame is established and the burner igniter turns off (if wired for interrupted ignition), simulate ﬂame failure by pulling the cord set out of the solenoid valve.

3.At ﬂame loss, the control will enter Relight mode. The control will immediately turn the igniter on.

4.After the 15 second lockout time, the control will lock out the burner. Verify that the burner motor and igniter are off and that the burner oil solenoid valve (if used) is not energized.

5.Push the cord set back in.

6.To reset the control from lockout, turn off power to the control for at least 2 seconds.

7.Turn power on and verify that the burner lights.

8.End the call for heat.

•Insure that all control wiring is correct prior to securing the control. Consult equipment manual for details.

GeniSys Control 24V Control Installation and Operation Manual

7559 specifications

Beckett 7559 is an advanced pump system designed for residential and commercial applications where efficient water management is essential. Known for its durability and reliability, the Beckett 7559 integrates several cutting-edge technologies, making it a popular choice among homeowners and industry professionals alike.

One of the standout features of the Beckett 7559 is its powerful motor, which is engineered to deliver high performance while maintaining energy efficiency. The motor operates at a low noise level, ensuring that the pump does not disrupt the tranquility of residential or garden environments. This makes it ideal for applications such as water fountains, ponds, and other water features where noise could be a concern.

The Beckett 7559 is equipped with a thermally protected motor that safeguards against overheating, extending the life of the pump and minimizing maintenance requirements. The unit also includes an integrated flow rate control, which allows users to customize water flow according to their specific needs. This feature not only enhances versatility but also optimizes water usage, contributing to eco-friendly practices.

Another remarkable characteristic of the Beckett 7559 is its robust construction. The pump is constructed with corrosion-resistant materials, ensuring that it can withstand exposure to various environmental factors, including water chemicals and changing weather conditions. This resilience makes the Beckett 7559 an excellent choice for use in tough outdoor conditions while maintaining aesthetic appeal.

The design of the Beckett 7559 also allows for easy installation and maintenance. The user-friendly interface ensures that even those with limited technical knowledge can set up and manage the pump with ease. Moreover, a variety of connectors and fittings are often included, making it compatible with a wide range of systems and configurations.

In summary, the Beckett 7559 stands out in the market for its powerful and energy-efficient motor, thermal protection features, customizable flow rate control, and durable construction. Designed for reliability and ease of use, it remains a top choice for effective water management in various applications. Whether for decorative ponds, fountains, or effective drainage solutions, the Beckett 7559 promises efficient performance and long-lasting use.