WIRING DIAGRAMS
Heat Pump Connections
If you do not have a heat pump system, refer to fi gures
You can confi gure the thermostat for use with the following heat pump systems.
HEAT PUMP TYPE 1 (HP 1). Single stage compressor system; gas or electric backup.
HEAT PUMP TYPE 2 (HP 2).
After wiring, see INSTALLER CONFIGURATION section for proper thermostat confi guration.
Figure 3 – Heat Pump Systems
JumperJumper
| L | O/B | Y | Y2 | W/E | W2 | G | RH | RC | C |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| NOTE: If your system does | |
System |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| O |
|
|
|
|
|
| Heat Mode | Blower/ |
|
|
|
|
|
| not provide an E connection, | |||
Heat Pump 1 |
|
| No |
|
| 2nd Stage. |
|
|
|
|
|
| jumper W2 to W/E to use | ||||||||
Energized in |
|
|
|
| Emergency | Circulator |
|
|
|
|
|
| the Auxiliary Heat in the | ||||||||
|
| Output |
|
|
|
|
|
|
|
| |||||||||||
(HP1) | Cool Mode |
|
|
|
| Mode 2nd | Fan Energized |
|
|
|
|
|
| ||||||||
| Fault Indicator | Heat and |
|
| Emergency | 24 Volt | 24 Volt | Optional* | Emergency Mode. | ||||||||||||
| or System |
|
| Cool Mode |
|
| Stage | on Call for | 24 Volt |
| |||||||||||
| Malfunction | B | 1st Stage |
|
| Mode |
|
| Heat or Cool. | (Hot) | (Hot) | (Com- |
| ||||||||
|
|
| Heat Mode | * Common connection | |||||||||||||||||
| Switch | Energized in | (Compressor) | 2nd | 1st Stage | Set Elect/Gas | Heat | Cool | mon) | ||||||||||||
Heat Pump 2 | Heat, Off, |
|
| Stage |
|
| 3rd Stage. | Option for |
|
|
|
|
|
| required for fault or | ||||||
|
|
|
| Emergency |
|
|
|
|
|
| |||||||||||
(HP2) | Emergency |
|
| (Com- |
|
| Emergency |
|
|
|
|
|
| malfunction indication. | |||||||
|
|
| Mode |
|
| pressor) |
|
| Mode 2nd | Mode |
|
|
|
|
|
| |||||
|
|
|
|
|
|
| Stage |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
System Malfunction | NEUTRAL |
|
Module | 120VAC | |
| 24VAC | |
| HOT |
|
| CLASS II |
|
| TRANSFORMER |
|
Single Stage and Multi-Stage Connections
Refer to equipment manufacturers’ instructions for specifi c system wiring information.
This thermostat is designed to operate a
You can confi gure the thermostat for use with the following fossil fuel systems:
SINGLE STAGE (SS 1) gas, oil or electric.
After wiring, see INSTALLER CONFIGURATION section for proper thermostat confi guration.
Figure 4 – Single Stage or Multi-Stage System (No Heat Pump) with Single Transformer
Jumper
L | O/B | Y | Y2 W/E | W2 | G | RH RC | C |
System
Single |
| O |
| No |
|
| Blower/ |
|
|
| |
Stage 1 | Fault | Energized Constantly |
|
| No Output | Circulator |
|
|
| ||
| Output |
|
|
|
| ||||||
(SS1) | Indicator | in Cool Mode |
| Heat |
| Fan Energized | 24 Volt | 24 Volt | Optional* | ||
|
| Cool Mode |
|
| on Call for | ||||||
| or |
|
| Mode |
| Cool (and | (Hot) | (Hot) | 24 Volt | ||
| System | B | 1st Stage |
|
| (Com- | |||||
Multi- | Cool | 1st Stage | Heat Mode | Heat if | Heat | Cool | |||||
Malfunction |
| mon) | |||||||||
Stage 2 | Energized Constantly |
| Mode |
| 2nd Stage | configured |
|
| |||
Switch | in Heat, Off, |
|
|
|
|
| |||||
(MS2) |
|
| 2nd |
|
| for Electric |
|
|
| ||
|
| Emergency |
| Stage |
|
| Heat) |
|
|
| |
|
| Mode |
|
|
|
|
|
|
|
|
*Common connection required for fault or
malfunction indication.
System Malfunction Module
NEUTRAL
24VAC
HOT
120VAC
CLASS II
TRANSFORMER
3