OWNER’S MANUAL
OPERATING
HEATER
Continued
MANUAL LIGHTING
PROCEDURE
1.Follow steps 1 through 5 under Light- ing Instructions, page 12.
2.With control knob pressed in, strike match. Hold match to pilot until pi- lot lights.
3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Follow steps 8 and 9 under Lighting Instruc- tions, page 12.
INSPECTING
BURNER
Check pilot flame pattern and burner flame pattern often.
PILOT FLAME PATTERN
Figure 20 shows a correct pilot flame pattern. Figure 21 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touch- ing the thermocouple. This will cause the thermocouple to cool. When the thermo- couple cools, the heater will shut down.
If pilot flame pattern is incorrect, as shown in Figure 21
•turn heater off (see To Turn Off Gas to Appliance, page 11 for
•seeTroubleshooting, pages 14 through 16
Pilot Burner
Thermocouple
GOOD PILOT/LP | GRH/OV 007 |
Figure 20 - Correct Pilot Flame Pattern
WARNING: If yellow tipping occurs, your heater could pro- duce increased levels of carbon monoxide. If burner flame pat- tern shows yellow tipping, follow instructions below.
NOTICE: Do not mistake orange flames with yellow tipping. Dust or other fine particles enter the heater and burn causing brief patches of orange flame.
If burner flame pattern is incorrect, as shown in Figure 23
•turn heater off (see To Turn Off Gas to Appliance, page 11 for
•seeTroubleshooting, pages 14 through 16
1/2 GLASS HEIGHT
Models
Figure 22 - Correct Burner Flame Pattern
Yellow
Tipping
1/2 GLASS HEIGHT
Figure 23 - Incorrect Burner Flame Pattern
CLEANING AND MAINTENANCE
ODS/PILOT AND BURNER
•Use a vacuum cleaner, pressurized air, or small, soft bristled brush to clean.
CLEANING BURNER PILOT AIR INLET HOLE
We recommend that you clean the unit every 2,500hoursofoperationoreverythreemonths.
We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly.
1.Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.
2.Inspect burner, pilot for dust and dirt.
3.Blow air through the ports/slots and holes in the burner.
Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 24). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.
Pilot Air Inlet
Hole
Thermocouple
Pilot Burner
WARNING: Turn off heater and let cool before cleaning.
Pilot Assembly
BAD PILOT/LPGRH/OV 008
Figure 21 - Incorrect Pilot Flame Pattern
BURNER FLAME PATTERN
Figure 22 shows a correct burner flame pattern. Figure 23 shows an incorrect burner flame pattern. Theincorrectburnerflamepatternshows yellow tipping of the flame. It also shows the flame higher than 1/2 the glass panel height.
CAUTION: You must keep control areas, burner, and circu- lating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a quali- fied service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.
Figure 24 - Pilot Inlet Air Hole
CABINET
Air Passageways
•Use a vacuum cleaner or pressurized air to clean.
Exterior
•Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabi- net to remove dust.
105564 | 13 |