Firex Model PB, Model C, Model B, Model E warranty Where YOU should Install Your Smoke Alarms

Page 3

You should use both battery-powered and direct-wired 120-volt AC-powered smoke alarms. Since A SMOKE ALARM WILL NOT WORK WITHOUT POWER, having alarms that will work from two different power sources can give you extra protection in case of a dead battery, or an AC power failure.

Using a smoke alarm in a smoky area like a kitchen, or in a high humidity area near a shower, can cause false alarms. DO NOT REMOVE YOUR BATTERY TO QUIET THE ALARM. DO NOT TAKE THE ALARM DOWN. DO NOT SHUT OFF THE POWER TO THE ALARM. IF YOU HAVE A FALSE ALARM, TRY WAVING A TOWEL NEAR THE ALARM TO CLEAR THE SENSING CHAMBER. A SMOKE ALARM WILL NOT HELP PROTECT YOU IF IT IS NOT POWERED, OR THE UNIT IS REMOVED. An alarm with a FALSE ALARM CONTROL feature should be used to minimize these nuisance alarms, where allowed by state and local codes.

A SMOKE ALARM MAY NOT ALWAYS WARN YOU ABOUT FIRES CAUSED BY CARELESSNESS OR SAFETY HAZARDS SUCH AS SMOKING IN BED, VIOLENT EXPLOSIONS, ESCAPING GAS, IMPROPER STORAGE OF FLAMMABLE MATERIALS, OVERLOADED ELECTRICAL CIRCUITS, NATURAL CAUSES SUCH AS LIGHTNING, CHILDREN PLAYING WITH MATCHES AND ARSON. Fire prevention is your best safeguard.

Installing smoke alarms may make you eligible for lower insurance rates, but SMOKE ALARMS ARE NOT A SUBSTITUTE FOR INSURANCE. Home- owners and renters alike should continue to insure their lives and properties.

WHERE YOU SHOULD INSTALL YOUR

SMOKE ALARMS

The National Fire Protection Association’s (NFPA) Standard 74, Section 2-1 provides information regarding the smoke detection equipment required within the family unit.

Section 2-1.1.1 reads as follows:

“Smoke detectors shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit including basements and excluding crawl spaces and unfinished attics.

The provisions of 2-1.1.1 represent the minimum number of detectors required by this standard. It is recommended that the householder consider the use of additional smoke or heat detectors for increased protection for those areas separated by a door from the areas protected by the required smoke detectors under 2-1.1.1 above. The recommended additional areas are the living room, dining room, bedroom(s), kitchen, attic (finished or unfinished), furnace room, utility room, basement, garage (attached or unattached), and hallways not included in Section 2-1.1.1 above. However, the use of additional detectors remains the option of the householder.”

This equipment should be installed in accordance with the National Fire Protection Association’s Standard 74, NFPA, Batterymarch Park, Quincy, MA 02269.

THIS STANDARD MEANS YOU SHOULD INSTALL AND USE A SMOKE ALARM IN EVERY ROOM AND AREA OF YOUR HOUSEHOLD OR BUILDING FOR GOOD PROTECTION.

THE FOLLOWING INFORMATION WILL HELP YOU SAFELY LOCATE YOUR SMOKE ALARMS:

•Do install your smoke alarms in accordance with all applicable laws, regulations, standards and codes.

•Do install a smoke alarm in the hallway outside of every bedroom area. If the bedroom has a door, there must be a smoke alarm inside and outside the bedroom. See Figure 1. If your home or residence has two bedroom areas, a smoke alarm must be placed outside the second bedroom area, and inside the bedroom(s) if they have doors. See Figure 2.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Important Information about Your Smoke Alarm ContentsWhat Smoke Alarms will not do What Smoke Alarms can doWhere YOU should Install Your Smoke Alarms Family Room Where YOU should not Install Smoke Alarms Important Information Smoke Alarm Safety Checklist What to do if There is a Fire in Your Home Follow Safety Rules and Prevent Hazardous SituationsWeekly Testing of Your Smoke Alarm HOW to Install Your Smoke AlarmTo Replace the Battery Taking Care of Your Smoke AlarmReplacing the Battery Needs ServiceUsing the Tamper Resist Locking Mechanism Special Smoke Alarm Features Year Limited Smoke Alarm Warranty Warranty Information

Model B, Model C, Model E, Model PB, A specifications

Firex is a prominent brand known for its cutting-edge fire safety technology, offering a range of models designed to cater to various safety needs across different environments. Among its notable products, the Firex A, Model PB, Model E, Model C, and Model B stand out for their advanced features, innovative technologies, and reliable characteristics.

Firex A is renowned for its compact design, which makes it suitable for residential settings. One of its main features is the dual-sensor technology that combines both photoelectric and ionization sensors. This feature allows the alarm to detect a wide range of fire types, from smoldering flames to fast-flaming fires. Additionally, the Firex A is equipped with a voice alarm that clearly communicates danger, enhancing user awareness and response times.

Model PB, designed for commercial use, incorporates advanced detection technology to provide quicker responses to smoke and heat. This model features a multi-sensor system that utilizes both optical and thermal sensors, ensuring it can react to various fire scenarios efficiently. Moreover, the Model PB includes a smart connectivity option, allowing users to integrate it into a larger fire safety management system, facilitating real-time monitoring and alerts.

Model E is specifically tailored for industrial applications, boasting robust features that meet stringent regulatory standards. It is built to function in extreme conditions, featuring a weather-resistant casing and enhanced sensitivity settings. One of its standout characteristics is its ability to filter out false alarms caused by dust or steam, thereby ensuring it operates reliably in challenging environments. Additionally, Model E can connect with other safety devices to create a synchronized alert system.

The Model C presents a balance of affordability and performance. Ideal for public spaces such as schools and offices, this model comes with a straightforward installation process and user-friendly interface. It features a built-in battery backup that ensures functionality during power outages. The Model C also has a unique tamper-resistant design, preventing unauthorized removal or disconnection, which enhances overall safety.

Finally, Model B is designed for high-occupancy environments, incorporating features like interconnected alarms that activate multiple units in case of an emergency. This model also emphasizes energy efficiency, utilizing low-power technology that reduces overall operational costs. With its sleek design and high sensitivity, Model B is an excellent choice for hotels, theaters, and similar venues.

In summary, Firex offers a diverse range of fire safety solutions, each tailored to specific needs with advanced technology, notable features, and robust characteristics that ensure safety and reliability in various settings.
Top Page Image Contents