Troubleshooting, Warranty Information

TROUBLESHOOTING

! DANGER: Always turn off power at main fuse box or circuit breaker before taking trouble- shooting action.

!WARNING: DO NOT disconnect battery or AC power to quiet an unwanted alarm. This will remove your protection. Fan the air or open a window to remove smoke or dust.

PROBLEM	SOLUTION

Smoke alarm does not	1. Check that AC power
sound when tested.	is turned on.
NOTE: Push test button for	2. Turn off power. Remove smoke
NOTE: Push test button for	alarm from mounting plate and:
at least five (5) seconds while	a. check that connector
testing!	plug is securely attached.
	b. check that battery is proper-
	ly attached to connector.
	3. Clean smoke alarm.

LED blinks and alarm beeps	Battery is low – REPLACE IT
simultaneously every 60 seconds.	IMMEDIATELY!

LED blinks and 30 seconds later	Unit inoperable. REPLACE OR
alarm beeps – repeats at 60	RETURN FOR REPAIR
second intervals.	IMMEDIATELY!

Smoke alarm beeps about	Turn off power and replace
once a minute.	battery. See “Battery Replacement”
	in the MAINTENANCE AND
	CLEANING section.

Smoke alarm sounds	1. Clean smoke alarm.
unwanted alarms intermit-	See “Cleaning” in the
tently or when residents	MAINTENANCE AND
are cooking, taking	CLEANING section
showers, etc.	2. Hire an electrician to move
	smoke alarm to a new location.
	See SMOKE ALARM
	PLACEMENT

Interconnected smoke	Press and hold test button for at
alarms do not sound when	least three seconds after the first
system is tested.	unit sounds.

The alarm sounds different	The alarm is operating correctly
than I’m used to. It starts and	This alarm features the
stops.	internationally recognized horn
	signal for evacuation. The horn
	pattern is 3 short beeps followed
	by a 2 second pause and then
	repeats.

REPLACE OR RETURN THE ALARM IF THE PUSH-TO-TEST FUNCTION DOES NOT OPERATE PROPERLY AFTER FOL- LOWING THE PROCEDURES OUTLINED ABOVE (see REPAIR on page 7).

WARRANTY INFORMATION

5-YEAR LIMITED SMOKE ALARM WARRANTY AND

10-YEAR LIMITED ULTRALIFE U9VL-J LITHIUM BATTERY WARRANTY (WHEN SOLD WITH INVENSYS CONTROLS AMERICAS SMOKE ALARM)

Invensys Controls Americas warrants to the original consumer purchaser each new smoke alarm to be free from defects in material and workmanship under normal use and service for a period of five (5) years from the date of purchase. For Invensys Controls Americas smoke alarms sold with an Ultralife U9VL-J 9-volt battery, Invensys Controls Americas warrants to the original consumer purchaser each new Ultralife U9VL-J 9-volt battery to be free from defects in material and workmanship under normal use and service for a period of ten (10) years from the date of purchase. Invensys Controls Americas agrees to repair or replace, at its option, any defective smoke alarm or Ultralife U9VL-J 9-volt battery (when sold with Invensys Controls Americas smoke alarm) provided that it is returned with postage prepaid and with proof of pur- chase date to Invensys Controls Americas. This warranty does not cover damage resulting from accident, misuse or abuse or lack of reasonable care of the product. This warranty is in lieu of all other express warranties, obligations or liabilities. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO A PERI- OD OF FIVE (5) YEARS FOR THE SMOKE ALARM AND TEN (10) YEARS FOR THE ULTRALIFE LITHIUM U9VL-J 9-VOLT BATTERY (WHEN SOLD WITH INVENSYS CONTROLS AMERICAS SMOKE ALARM) FROM PURCHASE DATE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO CASE SHALL INVENSYS CONTROLS AMERICAS COMPANY BE LIABLE FOR ANY INCIDENTAL OR CON- SEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY ITS NEGLIGENCE OR FAULT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other legal rights which vary from state to state. This smoke alarm’s manufacture and distribution are licensed by the U.S. Nuclear Regulatory Commission. This product meets all the requirements of U.L. Standard 217.

191 E. North Avenue
Carol Stream, Illinois 60188 USA
www.invensyscontrols.com
©2006 Invensys Controls	110-628F

FADC specifications

Firex FADC, or Fire Detection and Control Systems, is a cutting-edge solution designed to enhance fire safety in various environments, from industrial facilities to residential buildings. The primary objective of Firex FADC is to provide comprehensive fire detection, monitoring, and response capabilities, ensuring the protection of lives and property.

One of the standout features of Firex FADC is its advanced smoke detection technology. Incorporating both photoelectric and ionization sensors, this system can quickly identify different types of fires, including slow-burning or fast-flame ones. The dual-sensor approach ensures a higher rate of detection while minimizing false alarms, a common challenge in traditional fire detection systems.

Another critical aspect of Firex FADC is its integration with smart building technologies. Utilizing the Internet of Things (IoT), the system can interface with building management systems, allowing for real-time monitoring and remote management. This integration facilitates rapid response times and enhances situational awareness during emergencies. Additionally, the Firex FADC can send alerts to designated personnel and emergency services, streamlining the communication process during a fire incident.

Firex FADC also boasts an intuitive user interface designed for ease of use. The system provides clear visual notifications and audible alerts, ensuring that occupants are promptly informed of any potential dangers. Furthermore, the system is equipped with a self-testing feature, enabling regular checks to verify operational readiness without manual intervention.

The installation of Firex FADC is user-friendly, allowing for seamless incorporation into both new and existing structures. Its modular design allows for scalability, meaning that additional sensors and modules can be added as needed to meet evolving safety requirements.

Firex FADC stands out with its robust data analytics capabilities. By utilizing machine learning algorithms, the system can analyze historical data and patterns, enabling predictive maintenance and trend analysis. This proactive approach not only enhances the efficacy of fire detection but also helps in reducing operational costs by minimizing downtime and maintenance needs.

In summary, Firex FADC represents a significant advancement in fire safety technology. By combining sophisticated detection capabilities, smart integration, user-friendly interfaces, and data analytics, it empowers organizations and homeowners alike to better protect their lives and properties from the threat of fire. This innovative approach makes Firex FADC a vital tool in the ongoing fight against fire hazards.