Honeywell XL 800 SERIES manual Connecting via C-Bus, Connecting HMIs or Laptops

Page 17

Excel 800

Mounting/Dismounting Modules

Fig. 23. Locking the electronic module

NOTE: The red locking mechanism will not close if the electronic module is not properly mounted.

Dismounting Electronic Modules

NOTE: Electronic modules can be removed from the socket or inserted into the sockets without switching off the power supply. The behavior of connected field devices must be taken into consideration.

Open the red locking mechanism by sliding it to the left and then gently pull the electronic module out of the terminal socket.

Fig. 24. Dismounting the electronic module

Connecting via C-Bus

Via C-Bus, an XCL8010AU Controller Module can be connected to other controller systems to form a network.

Connecting to the Controller

Connect the C-Bus to the XCL8010AU Controller Module as follows:

Input to C-Bus terminals 8 and 9

Output to C-Bus terminals 5 and 6

Do not connect the C-Bus to the cabinet earth or any other earth ground points

Setting the C-Bus Termination Switch

Set the C-Bus termination switch S1 appropriately.

Fig. 25. C-Bus termination switch S1

Table 11. XCL8010AU C-Bus termination switch settings

 

switch setting

baud rate

 

S1

 

 

 

9.6k all

Up to 9600 baud (default setting)

 

 

 

 

76k mid

Up to 76800 baud without bus termination

 

 

 

 

76k end

Up to 76800 baud with bus termination

 

 

 

Shielding

In principle, data transmitting cables should be shielded in case of RFI.

On the controller side, connect the shield to terminals 7 and 10.

On the side of the device, connect the shield to the respective terminals.

Do not connect it to the cabinet ground or any other ground points.

Connecting HMIs or Laptops

Laptops or HMIs, e.g., XI582, can either be connected via the HMI interface of the XCL8010AU Controller Module or via the LONWORKS interface.

Connecting the XI582 Operator Interface

Connect the XI582AH Operator Interface to the HMI interface or LONWORKS interface of the XCL8010AU Controller Module by means of

the XW882 cable or

the XW582 cable connected with an XW586 cable.

17

EN1B-0410GE51 R0908A

Image 17
Contents XL 800 Series Trademark Information TroubleshootingGeneral General Before InstallationInstallation Wiring XL800 Series Power Consumption Modules BUS Modules Overview Description of the XCL8010AU Controller ModuleDescription of the XCL8010AU Controller Module Excel Typical 14507287-001 Power Module wiringController Transformer GRN Smoke Control Configuration Technical DataInterfaces and Bus Connections System DataTypical Power Limited Circuit for XL800 Panel ResetConnecting Single Bus Controller Systems Data File Set-UpConnecting I/O Modules to the XCL8010AU Connecting I/O ModulesXCL8010AU, I/O Modules on Single Rail Multiple Rails in Single CabinetHEX switch settings and addresses Address Setting Address of Panel Bus I/O ModulesMounting/Dismounting Modules Setting the I/O Bus SwitchLonworks Bus Topologies Bus TopologiesMounting/Dismounting Controller/Sockets Connecting SocketsMounting Sockets Risk of malfunctionMounting/Dismounting Electronic Modules Disconnecting SocketsDismounting Sockets Mounting Electronic ModulesConnecting HMIs or Laptops Connecting via C-BusConnecting Laptops XL-Online/CARE FeaturesLonworks Service LED and Button XCL8010AU TerminalsHMI Interface Reset ButtonBus Tx LED and Rx LED Bus Switch S2 Alarm and Power LEDsWatchdog Status Modem InterfaceBus Termination Switch S1 Common FeaturesDescription of the I/O Modules MemoryTerminals Types of Analog Input Modules FeaturesAnalog Input Modules XFL821AU Analog Input Module XFL821AU Connection ExamplesAnalog Output Modules Technical DataTypes of Analog Output Modules TerminalsDamage to the electronic module Modules with Manual OverridesXFL822AU Connection Example Signal Comment Minal Excel 800 Binary Input Modules Type Description HousingBinary Input Modules Types of Binary Input ModulesXF823AU Connection Examples Status LEDsTypes of Relay Output Modules Excel 800 Relay Output Modules Type Description HousingRelay Output Modules Status LEDs with Manual Overrides Permissible LoadsXFR825AU connection example XF824AU connection exampleTesting Wiring Connections TroubleshootingTroubleshooting on the XCL8010AU Controller Power LED greenXCL8010AU alarm LED Case Alarm LED Meaning Remedy Alarm LED redLonworks Service LED HMI Tx and Rx LEDs Bus Tx and Rx LEDsPower LED of I/O Modules Modules TroubleshootingService LED of I/O modules Case Meaning Remedy Service LED of I/O ModulesExcel 800Troubleshooting Automation and Control Solutions

XL 800 SERIES specifications

The Honeywell XL 800 Series represents a significant advancement in the realm of flight management systems, tailored for general aviation aircraft. This series stands out due to its combination of state-of-the-art technology, user-friendly interface, and comprehensive functionality, all designed to enhance safety and operational efficiency for pilots.

One of the main features of the XL 800 Series is its advanced flight planning capabilities. The system is equipped with a robust database that allows pilots to create, modify, and execute flight plans with unprecedented ease. The built-in terrain awareness tools provide real-time information about geographical obstacles, helping mitigate the risk of Controlled Flight Into Terrain (CFIT). The intuitive graphical user interface offers a clear view of the flight path, airspace constraints, and available alternatives, enabling pilots to make informed decisions.

The XL 800 Series also boasts cutting-edge navigation technologies, including GPS, RNAV, and WAAS (Wide Area Augmentation System) support. These technologies ensure that flights are accurately tracked and that pilots remain on course, enhancing navigation reliability. Additionally, the system includes advanced autopilot features, which allow for smoother transitions during flight phases and can significantly reduce pilot workload.

Another notable characteristic of the XL 800 Series is its connectivity. The system supports data link services that enable real-time weather updates and air traffic control communication. This connectivity not only improves situational awareness, but it also equips pilots with the necessary tools to adapt to changing flight conditions promptly.

Furthermore, the Honeywell XL 800 Series prioritizes safety with integrated safety features, including enhanced cockpit alerting systems. These systems proactively notify pilots of potential hazards, such as deviations from the flight path or adverse weather conditions, ensuring that safety remains paramount throughout the flight.

In summary, the Honeywell XL 800 Series encapsulates a wide array of features and technologies that serve to elevate the flying experience for general aviation pilots. Through its emphasis on flight planning, navigation, connectivity, and safety, it stands as a reliable and sophisticated solution that meets the demands of modern aviation. Whether enhancing safety, improving navigation accuracy, or simplifying flight planning, the XL 800 Series is a premier choice for those seeking an advanced flight management system.