Honeywell 800-04433V1 manual PowerBoost

Page 6

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide

Note: Refer to the diagram on page 5, and to the Wiring Diagram on the inside of the back cover of this manual for all wiring information.

5.Mount the Wall Outlet Box to an un-switched facility power outlet and run a conduit to the cabinet.

6.Route 16AWG (minimum) wire from the transformer, through the conduit. Pass the wires through the Ferrite Filter, then loop the wires back through again making a loop. Connect the wires to the PowerBoost1 AC terminals. DO NOT plug the transformer in.

7.Connect and route 16AWG (minimum) insulated wire from facility power ground (typically a cold water pipe) to the cabinet's ground post. Ensure all ground connections are tight.

8.Connect the Ethernet cable and the Telco 1 and Telco 2 lines. If you choose to use an optional Cabinet Tamper Switch (if the control panel supports it) mount and wire it.

Note: The Ethernet cable, Telco 1, Telco 2 lines, and the optional cabinet Tamper Switch (if used) must be run through conduit.

9.Verify the PowerBoost1 module DIP switches are configured as shown below.

PowerBoost 1

-V0

ON

 

 

 

 

 

 

 

 

 

008-COM-iPGSM

1

2

3

4

5

 

ON

1 2 3 4 5

(Switch handle = white)

10.Ensure the following:

LED Display board is fully seated.

All wiring terminals and connectors are tight.

All wiring has been completed and secured with cable ties.

11.Install the battery (not supplied). Plug the power transformer in, and attach the battery cable.

4

Image 6
Contents IPGSM-COM Contents Installation General InformationOperation Activate the SIM and Setup the Customer Account Register the Communications Module with AlarmNetDetermine the Signal Strength and Select a Location Mount and WirePowerBoost Battery Wall Outlet BOX K14358 ConduitTo Facility Ground Conduit Program the Communications Module 7720P ProgrammerDone Configure the Fire Panel IPGSM-COM Trouble Detection InformationTest the System Dialer Capture Module Information LED Board InformationPowerBoost1 Module Information ActiveIGSM Communications Module Information OFF Normal Slow Blink Loss of communication withIPGSM-COM Specifications SpecificationPage Wiring Diagram + BatteryÊ800-04433V1Š

800-04433V1 specifications

The Honeywell 800-04433V1 is a robust and efficient product designed to enhance the operational capabilities of various systems. As part of Honeywell's extensive portfolio, this device is engineered with advanced technologies that cater to both industrial and commercial applications, emphasizing reliability and user-friendly operation.

One of the standout features of the Honeywell 800-04433V1 is its versatility. It is compatible with a wide range of systems, making it an ideal choice for facilities looking to upgrade their operations without overhauling existing infrastructure. The device supports several communication protocols, ensuring seamless integration into various control architectures.

The Honeywell 800-04433V1 is built with advanced sensing technologies that provide accurate data readings and measurements. This high level of precision is crucial for applications requiring stringent compliance with safety and performance standards. Its robust sensors are capable of operating under challenging environmental conditions, ensuring consistent performance regardless of external factors.

Energy efficiency is another prominent characteristic of the Honeywell 800-04433V1. The device is designed to minimize power consumption while maintaining optimal operational performance. This not only helps businesses reduce operational costs but also contributes to a smaller carbon footprint, making it a sustainable choice for modern enterprises.

The user interface of the Honeywell 800-04433V1 is intuitive and easy to navigate, allowing operators to monitor and control processes with minimal training. The device typically features a clear display and programmable settings, enabling users to customize operations according to specific needs and preferences. This ease of use translates into increased productivity and more streamlined workflows.

In terms of durability, the Honeywell 800-04433V1 is constructed with high-quality materials that can withstand the rigors of industrial environments. Its design often incorporates protective features such as moisture resistance and shock absorption, which extend the device's lifespan and reduce the potential for maintenance and replacement costs.

Moreover, Honeywell prioritizes innovation, and the 800-04433V1 reflects this commitment through its ongoing support and software updates. This ensures that users can benefit from the latest advancements in technology, further enhancing their operational capabilities.

In summary, the Honeywell 800-04433V1 is an advanced device designed for efficiency, flexibility, and durability. With its intuitive user interface, energy-saving characteristics, and compatibility with various systems, it stands out as a top choice for businesses looking to enhance their operational effectiveness.