Locations To Avoid, Installation Instructions

1.Recommended Locations for Smoke Alarms

•Put smoke alarms at both ends of a bedroom hallway or large room if the hallway or room is more than 30 ft (9.1 m) long.

•Install Smoke Alarms on sloped, peaked or cathedral ceilings at or within 3ft (0.9m) of the highest point (measured horizontally). NFPA 72 states: “Smoke alarms in rooms with ceiling slopes greater than 1 ft in 8 ft (.3m in 2.4 m) horizontally shall be locat- ed on the high side of the room.” NFPA 72 states: “A row of detectors shall be spaced and located within 3 ft (0.9m) of the peak of the ceiling measured horizontally” (see figure 2).

2.Locations To Avoid

•In the garage. Products of combustion are present when you start your automobile.

•Less than 4” (10cm) from the peak of an “A” frame type ceiling.

•In an area where the temperature may fall below 40ºF or rise above 100ºF, such as garages and unfinished attics; this should also include electrical boxes exposed to these environments.

•In dusty areas. Dust particles may cause nuisance alarm or failure to alarm.

•In very humid areas. Moisture or steam can cause nuisance alarms.

•In insect-infested areas.

•Smoke alarms should not be installed within 3 ft (.9m) of the following: the door to a kitchen, the door to a bathroom containing a tub or shower, forced air supply ducts used for heating or cooling, ceiling or whole house ventilating fans, or other high air flow areas.

•Kitchens. Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence feature or be a photo- electric type.

•Near fluorescent lights. Electronic “noise” may cause nuisance alarms.

•Smoke alarms are not to be used with detector guards unless the combination (alarm and guard) has been evaluated and found suitable for that purpose.

3. Installation Instructions

WIRING REQUIREMENTS

•This smoke alarm should be installed in a U.L. listed or recognized junction box. The mounting bracket is equipped to accommodate a 3.5 inch hole spacing on a round electrical box and a double-gang rectangular electrical enclosure. All connections should be made by a qualified electrician and all wiring used shall be in accordance with articles 210 and 300.3(B) of the U.S. National Electrical Code ANSI/NFPA 70, NFPA 72 and/or any other codes having jurisdiction in your area. This unit consumes four cubic inches of interior space of the junction box volume. This figure should be used when calculating junction box volume.

•The multiple station interconnect wiring to the alarms must be run in the same raceway or cable as the AC power wiring. In addition, the resistance of the interconnect wiring shall be a maximum of 10 ohms.

•The appropriate power source is 120 Volt AC Single Phase supplied from a non-switchable circuit which is not protected by a ground fault interrupter.

•WARNING: This alarm cannot be operated from power derived from a square wave, modified square wave or modified sine wave inverters. These types of inverters are sometimes used to supply power to the structure in off grid installations, such as solar or wind derived power sources. These power sources produce high peak voltages that will damage the alarm.

Wiring Instructions for Quick Connect Harness

CAUTION! Turn off the main power circuit before wiring the alarm

•When alarms are interconnected, all interconnected units must be powered from a single circuit.

•A maximum of 18 Kidde devices may be interconnected in a multiple station arrangement. The interconnect system should not exceed the NFPA interconnect limit of 12 smoke alarms or 18 alarms {12 smoke and 6 other (heat, carbon monoxide, or similar alarms)}.

•When mixing models which have battery backup (i12040, i12060, i12080, 1275, 1276, 1285, 1296, PE120, PI2000, KN-COSM-IB, KN- SMFM-I, RF-SM-ACDC, HD135F, KN-COB-IC, KN-COP-IC) with models without battery backup, (i1220, 1235, KN-COSM-I, 120X, SM120X,CO120X, SL177i) be advised that the models without battery backup will not respond during an AC power failure.

820-1356 specifications

The Kidde 820-1356 is a smoke alarm that combines advanced safety features with user-friendly technology to provide a reliable solution for fire detection in homes and businesses. Understanding its main features, technologies, and characteristics is crucial for anyone considering an upgrade to their fire safety systems.

One of the standout features of the Kidde 820-1356 is its dual-sensor technology. This smoke alarm utilizes both photoelectric and ionization sensing methods, allowing it to detect different types of smoke more effectively. The photoelectric sensor is adept at sensing slow-burning fires, which produce larger smoke particles, such as those from smoldering furniture or electrical fires. The ionization sensor, on the other hand, quickly responds to fast-burning fires that generate smaller particles, like those from paper or flammable liquids. This combination enhances the alarm’s overall responsiveness, providing a faster response time in various fire situations.

In terms of design, the Kidde 820-1356 features a user-friendly interface. It includes a large test/silence button, which allows users to test the alarm’s functionality easily or silence it when necessary. The alarm also has a green power indicator light that lets you know it is functioning correctly, providing peace of mind at a glance.

Another important characteristic of this smoke alarm is its dependable power source. The Kidde 820-1356 operates on a sealed lithium battery that lasts for up to 10 years, eliminating the need for frequent battery replacements. This feature is particularly advantageous as it minimizes maintenance and ensures the alarm remains functional for an extended period. Additionally, the alarm emits a chirping sound when its battery is low to alert users to replace the unit.

The Kidde 820-1356 is also designed to be easy to install. With a quick-mount bracket and included hardware, users can install it in various locations around a home, including hallways, bedrooms, and living areas. This versatility ensures that critical areas are monitored effectively.

Overall, the Kidde 820-1356 stands out as a feature-rich smoke alarm that leverages advanced sensing technologies for optimal fire detection. Its user-friendly design, long-lasting power source, and ease of installation make it an excellent choice for enhancing fire safety in any environment. By selecting this reliable device, users can significantly reduce the risk of fire hazards and ensure the safety of their occupants.