Kidde 0918K, 440376 manual Locations to Avoid, Installation Instructions, Operation and Testing

Page 3

2. LOCATIONS TO AVOID

•In the garage. Products of combustion are present when you start your automobile.

•Less than 4” (10cm) from the peak of an “A” frame type ceiling.

•In an area where the temperature may fall below 40ºF or rise above 100ºF.

•In dusty areas. Dust particles may cause nuisance alarm or failure to alarm.

•In very humid areas. Moisture or steam can cause nuisance alarms.

•In insect-infested areas.

•Smoke alarms should not be installed within 3 ft (.9m) of the following: the door to a kitchen, the door to a bathroom containing a tub or shower, forced air ducts used for heating or cooling, ceiling or whole house ventilating fans, or other high air flow areas.

•Kitchens. Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence feature or be a photoelectric type.

•Near fluorescent lights. Electronic “noise” may cause nuisance alarms.

3. INSTALLATION INSTRUCTIONS

CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!

and arrow are facing up. Use the screws and anchors provided to secure the mounting plate (use 3/16” drill bit for anchors).

4.Battery installation instructions are provided on the inside of the battery door for Safety Light and Smoke Alarm use. To ensure proper installation of the Safety Light and Smoke Alarm battery follow the instructions.

CAUTION! MAKE SURE TO INSTALL THE PROPER LONG LIFE BATTERY (SEE SECTION 6) IN THE COMPARTMENT THAT POWERS THE SMOKE ALARM AND THE ALKALINE BATTERY IN THE COMPARTMENT THAT POWERS THE SAFETY LIGHT. REVERSING THESE WILL ELIMINATE THIS SMOKE ALARM’S LONGLIFE BATTERY CAPABILITY AND MAY DAMAGE THE SAFETY LIGHT.

5.When installing the battery, press the battery reminder finger down into the battery compartment and install the battery (see Figure 3).

CAUTION! IF THE BATTERY REMINDER FINGERS ARE NOT HELD DOWN IN THE BATTERY COMPARTMENT BY THE BATTERIES, THE BATTERY DOOR WILL NOT CLOSE, AND THE UNIT WILL NOT ATTACH TO

THE MOUNTING BRACKET.

6. Alignment marks are provided on the edge of the trim plate and the alarm. After

installing the mounting plate, place the alarm on the mounting plate with the align-

ment marks lined up. Twist the alarm in the direction indicated by the “ON” arrow

on the alarm cover (see Figure 4) until it locks in place.

When mounting in a hallway, the “A” line should be parallel with the hallway.

When wall mounting, the “A” line should be horizontal and the “UP FOR WALL MOUNTING” arrow must be pointing up.

7. USING TAMPER RESIST LOCKING PIN: To

make your smoke alarm somewhat tamper

resistant, a locking pin has been provided in

the bag with the screws and anchors. Using

this pin will deter children and others from

removing the alarm from the mounting plate.

FIGURE 1

FIGURE 2

Alignment Marks

InstallRemove

FIGURE 3

FIGURE 4

1.Remove the mounting plate from the back of the alarm by holding the mounting plate and twisting the alarm in the direction indicated by the “OFF” arrow on the alarm cover.

2.To insure aesthetic alignment of the alarm with the hallway or wall, the “A” line on the mounting plate must be parallel with the hallway when ceiling mounting or horizontal when wall mounting.

3.After selecting the proper smoke alarm location as described in Section 1, attach the mounting plate to the ceiling as shown in Figure 1. For wall mounting see Figure 2. Place mounting plate on the wall. Be sure the “UP FOR WALL MOUNTING “ text

To use the pin, insert it into the hole in the

 

side of the alarm after the alarm has been

FIGURE 5 Tamper Resist

installed on the mounting plate (see Figure 5).

 

Locking Pin

NOTE: THE TAMPER RESIST PIN WILL

HAVE TO BE REMOVED IN ORDER TO CHANGE THE BATTERIES. USE A LONG NOSE PLIERS TO PULL THE PIN OUT OF THE HOLE. IT IS NOW POS- SIBLE TO REMOVE THE ALARM FROM THE MOUNTING PLATE.

8.After installation, test your alarm by depressing and holding down the test button for several seconds. This should sound the alarm.

4. OPERATION AND TESTING

OPERATION: The smoke alarm is operating once a fresh battery is installed and test- ing is complete. When products of combustion are sensed, the unit sounds a loud 85db pulsating alarm until the air is cleared.

SAFETY LIGHT: The model 0918K has a Safety Light feature. When the smoke alarm ionization chamber senses smoke, the 85db horn will sound and the Safety Light will flash until the sensing chamber is cleared of smoke particles.

NOTE: THE SAFETY LIGHT IS NOT INTENDED TO SATISFY THE REQUIRE- MENTS FOR APPROVED ILLUMINATION UNDER VARIOUS LOCAL CODES. VERY THICK AND/OR DENSE SMOKE MAY OBSCURE THE LIGHT.

HUSH CONTROL: The “HUSH” feature has the capability of temporarily desensitizing the alarm circuit for approximately 7 minutes. This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The

Page 2 Page 4
Image 3
Page 2 Page 4
Contents DC4K Recommended Locations for Alarms Contents of this ManualMobile Home Installation Mounting Bracket Installation InstructionsOperation and Testing Locations to AvoidNuisance Alarms MaintenanceBattery Replacement Limitations of Smoke Alarms Good Safety HabitsNRC Information Service and Warranty TEN Year Limited WarrantyNfpa Required Protection Supplementary Warranty Information To Return Ultralife Battery to Ultralife Batteries INCTo Return Smoke Alarm to Kidde Safety

440376, 0918K specifications

The Kidde 0918K, model number 440376, is a leading smoke alarm designed to ensure safety and peace of mind for homeowners. This innovative device combines advanced technology with user-friendly features to provide reliable fire detection in residential settings.

One of the standout features of the Kidde 0918K is its dual-sensor technology. This smoke alarm utilizes both photoelectric and ionization sensing methods, effectively detecting a wide range of fire types. Photoelectric sensors excel at identifying slow-burning fires, such as those caused by smoldering materials, while ionization sensors are particularly adept at detecting fast-burning fires. This dual-sensor approach increases the overall effectiveness of the alarm, minimizing the chances of false alarms while ensuring a swift response to genuine fire threats.

Another significant characteristic of the Kidde 0918K is its user-friendly design. The unit incorporates a single testing/silence button, making it easy for users to test the alarm's functionality or silence it if a false alarm occurs. The simple interface allows homeowners to manage the device without extensive technical knowledge. Additionally, the alarm features a battery backup system, ensuring it remains operational during power outages, a crucial safety measure that underscores its reliability.

The Kidde 0918K also boasts an LED indicator that provides visual confirmation of the alarm’s status. The green LED light indicates when the unit is powered and functioning correctly, while a red LED signals when the alarm is triggered or when there’s an issue with the device. This clear visual communication makes it easier for users to monitor the alarm's performance.

With its compact and sleek design, the Kidde 0918K fits seamlessly into any home environment. Its straightforward installation process means that it can be mounted on walls or ceilings with minimal effort, allowing homeowners to enhance their safety measures quickly.

Durability is another key feature of the 0918K model, designed with high-quality materials to withstand various environmental conditions. It adheres to the highest safety standards, giving users confidence in its protective capabilities.

In conclusion, the Kidde 0918K, model number 440376, is a versatile smoke alarm that combines sophisticated sensing technology with ease of use and reliability. Its dual-sensor system, battery backup, LED indicators, and flexible installation options make it an essential safety device for any home.
Top Page Image Contents